Steve Wurster
Contributor

Well, Jim, I might offer to "trade" your saw for my Hammer K3, but I think your saw is bigger than my whole shop. To say nothing of the fact that I...

Gotcha. Yeah, It's definitely just a single-person shop in my basement. lol I don't plan on making any direct drop be 5 or less". There's only...

The empty wall to the "left" of the cyclone is taken up by my horizontal lumber rack. While I could in theory shorten that or even shift it and...

I don't even think I can enclose the cyclone if I have it in that location. LOL Seriously though, in that location the unit is effectively...

I've been occasionally checking this thread and was happy to see this. Congrats, Jim. Where about is this place?

It's a basement shop under the front portion of my house; there is no outside placement possible. My existing low-powered DC is in the exact same...

Unfortunately I don't really have another place to put the cyclone. Height limitations and the placement of various obstructions heavily limits...

I currently have a 5" line off my Super Dust Deputy in that exact same joist bay and down onto the far wall like shown in the picture. There's just...

You're not planning on going with Nordfab or some other equivalent "quick clamp" setup in a future shop, Jim? I'm debating going with the quick...

My shop is ~16x24, so fairly close to that of a typical 2-car garage. It's a basement shop though, so the ceiling height is low, and one "wall" is...

Yes, I use that port now, but connected to my Shop Vac or CT-MIDI depending on what I'm picking up. I use the Shop Vac for larger chips like with a...

Lisa, those are great, thanks. My drill press and sander live near each other, so I'm hoping to drop a line down on the wall behind the drill...

Yeah, I'm not sure about the piping length. My current piping is 5" HVAC stuff from the Borg, and I don't know if that would hold up to the...

I've thought about the Supercell a few times for my basement shop, given its smaller size. However I don't think it would work well in my...

Lisa, what did you do for your drill press and your Ridgid sander? I'm currently running a 5" trunk as well (via a 1.5HP DC w/ Super Dust Deputy),...

Update for those that were following this thread: I shipped the router (motor only) to Milwaukee back on February 3rd. I got email updates from...

Yeah, I wondered if those adapters would work. I'll double-check that with my rep when he's back in the office. That would be a nice solution.

I had that thought as well. I was wondering if I could build a "box" to go between the fan housing outlet and the filter stack's inlet that simply...

Ah, you've got the older clamp-style design. The current models use bolts instead, but it looks like there might be enough of them that I can at...

Great. Ah, it looks like the current manual shows 12 bolts, which would be 30 degree increments. Oooh, that just might work fine in my shop,...

Ole and Jim, perhaps one of you can answer this question: Can the barrel section of your DC be assembled in 15 degree increments, or 45 degree? ...

Jim, I will have to install it with the motor between the joists as well. But since the overall height of the unit is just barely taller than the...

Ole, thanks for the info. I assume that 26" is from the wall to the flange between the cyclone and the inlet sections? I think that would work fine...

The Super Cell is available with 14, 35, and 55 gallon drums, but obviously each one increases the overall height requirements of the unit (72" for...

Jim, I don't have any other known dimensions on the unit. All they provide is a general freestanding mount requirement, but not the size of the...

As Wes pointed out, I'm pretty sure that's manufactured by RUWI and just rebranded by Felder and others. The price is also much cheaper in Europe,...

I have French Cleats on sections of two walls in my shop. There's about 8' of cleats on the wall above my bench, and just under 6' of cleats on a...