View Profile: Brian Runau - Sawmill Creek Woodworking Community

Yesterday, 7:16 AM

Brian Runau started a thread basement shop humidity level setting in WorkShops

Curious, for those who have basement shops, what level humidity do you set your humidifier on for the summer? thanks Brian

5 replies | 184 view(s)

05-16-2022, 12:57 PM

Brian Runau replied to a thread How to replace Syder/Coupler on Supermax 16/32>? in General Woodworking and Power Tools

Spider is designed to wear and fail and is replaceable. Brian

16 replies | 696 view(s)

05-15-2022, 5:15 PM

Brian Runau replied to a thread How to replace Syder/Coupler on Supermax 16/32>? in General Woodworking and Power Tools

Traditionally, the color of spider designates it torque rating, so make sure to get the correct "color." Alignment of the coupling hubs is...

16 replies | 696 view(s)

05-03-2022, 4:34 PM

Brian Runau replied to a thread Nice packaging from virutex in General Woodworking and Power Tools

They could, if they chose too. I believe it costs more not to. Brian

7 replies | 567 view(s)

05-02-2022, 11:05 AM

Brian Runau replied to a thread Creeker's Past Week's Accomplishments in General Woodworking and Power Tools

Working on rededicating myself to meditation and stretching exercises. Mind over matter for me, I resist stuff that makes me feel better, go figure!...

7 replies | 590 view(s)

04-28-2022, 7:33 AM

Brian Runau started a thread Grizzly G0586 jointer fence square sage in General Woodworking and Power Tools

OK. Reminder, the fence was moving off square when I tightened the tilt mechanism, it was also moving off square when I turned it on and off. I...

3 replies | 405 view(s)

04-27-2022, 6:55 PM

Brian Runau replied to a thread Mistake Recovery - Domino mistake fixed by a domino in General Woodworking and Power Tools

Thanks. Brian

14 replies | 1003 view(s)

04-27-2022, 6:59 AM

Brian Runau replied to a thread How do I operate this tensioner? in General Woodworking and Power Tools

2nd vote for this. Bolt is bottom up so top but adjusts to increase or decrease downward pressure. Old design, but should work when adjusted. You...

12 replies | 1375 view(s)

04-26-2022, 6:56 PM

Brian Runau replied to a thread Mistake Recovery - Domino mistake fixed by a domino in General Woodworking and Power Tools

How did you cut the tenon to the correct size?

14 replies | 1003 view(s)

04-22-2022, 3:59 PM

Brian Runau replied to a thread mission bed design in Design Forum

Lee, I really appreciate your help and suggestions. Brian

9 replies | 934 view(s)

04-22-2022, 1:08 PM

Brian Runau replied to a thread mission bed design in Design Forum

Always a good idea, I was hoping I could make up my mind without doing this, but.... brian

9 replies | 934 view(s)

04-22-2022, 1:07 PM

Brian Runau replied to a thread mission bed design in Design Forum

Lee, I don't know the size of the bed in the photo, just something I grabbed off google. Where would you add the detail from the riser on the head...

9 replies | 934 view(s)

04-21-2022, 11:19 AM

Brian Runau replied to a thread mission bed design in Design Forum

In the pic there are 3 panels/2 dividers left to right. I am asking if 1 divider would look better on a queen. I just posted a picture of the top...

9 replies | 934 view(s)

04-21-2022, 8:53 AM

Brian Runau started a thread mission bed design in Design Forum

Planning on building something similar to this design in a platform bed. Two questions. 1. I see the three panels across the head/foot...

0 replies | 301 view(s)

04-21-2022, 8:52 AM

Brian Runau started a thread mission bed design in Design Forum

Planning on building something similar to this design in a platform bed. Two questions. 1. I see the three panels across the head/foot boards....

9 replies | 934 view(s)

04-19-2022, 4:42 PM

Brian Runau replied to a thread Mission, arts and crafts bed in Design Forum

I did look at these. thanks for the idea. thinking about using this on both ends, but think it might be to much. brian ...

6 replies | 834 view(s)

04-19-2022, 4:31 PM

Brian Runau replied to a thread Mission, arts and crafts bed in Design Forum

thanks I will investigate. brian

6 replies | 834 view(s)

04-19-2022, 7:52 AM

Brian Runau started a thread Grass F130100727204 in SawMill Creek Classifieds

Would anyone have 2 pair of this unit they would be willing to sell to me? Need them to finish up a project. Dynapro 15" 3D under mount units. ...

0 replies | 486 view(s)

04-19-2022, 5:43 AM

Brian Runau replied to a thread Mission, arts and crafts bed in Design Forum

I plan to make the leg so I have quarter sawn on all four faces and bevel the vertical edges on the post. I don't have the skill to fit cove...

6 replies | 834 view(s)

04-18-2022, 8:44 AM

Brian Runau started a thread Mission, arts and crafts bed in Design Forum

Planning on a build using a 4 x 4 posts with the edges beveled. Quarter saw oak. Using a solid panel on the head board foot board, I hate slats,...

6 replies | 834 view(s)

04-18-2022, 8:14 AM

Brian Runau replied to a thread Miter Saw Station in General Woodworking and Power Tools

Curious what you do at the miter station that requires precision? I built Norms version and use it as a chop saw station to break down 8ft lumber...

22 replies | 1582 view(s)

Brian Runau
Contributor

Mini Statistics

Recent Visitors

Basic Information

About Brian Runau

Signature

Statistics

Total Posts

General Information

Brian Runau Contributor

Mini Statistics

Recent Visitors

Basic Information

About Brian Runau

Signature

Statistics

Total Posts

General Information

Brian Runau
Contributor