View Profile: Rob Sack - Sawmill Creek Woodworking Community

Tab Content: All; Rob Sack; Friends; Photos

Older Activity
05-21-2023, 11:44 AM

Rob Sack replied to a thread Exactor Sliding Table in SawMill Creek Classifieds

Price dropped to $325.00 OBO

see more

1 replies | 794 view(s)
05-21-2023, 11:36 AM

Rob Sack replied to a thread Different cabinet door question in General Woodworking and Power Tools

Euro hinges will work with rabbeted doors. I've done it. I just can't remember if I used Grass or Blum hinges. See my previous post. A quick...

see more

11 replies | 724 view(s)
05-20-2023, 9:39 PM

Rob Sack replied to a thread Different cabinet door question in General Woodworking and Power Tools

As a side note, should you consider using European style concealed hinges, it's doable. I did a job years ago retrofitting some 3/8" lipped doors...

see more

11 replies | 724 view(s)
05-19-2023, 11:38 AM

Rob Sack replied to a thread Rough sawn doug fir paneling finish q'S in WorkShops

I still would seal the back side before installation. The exterior of my house is all tongue and groove redwood siding. We finished it with long...

see more

9 replies | 944 view(s)
05-17-2023, 4:02 PM

Rob Sack replied to a thread Hand-held corded belt sander recommendations? in General Woodworking and Power Tools

Although I rarely use a belt sander these days the best balanced sanders I have are the 3 x 21 Swiss made Bosch and the 4 x 24 Hitachi. I have had...

see more

37 replies | 2498 view(s)
05-13-2023, 2:29 PM

Rob Sack started a thread Multico Bench Top Mortiser in SawMill Creek Classifieds

Multico mortiser with 1/2 inch bit. Excellent condition. Very little use. Manufactured in England. Excellent build quality. This is the original...

see more

0 replies | 402 view(s)
05-10-2023, 9:10 PM

Rob Sack started a thread Exactor Sliding Table in SawMill Creek Classifieds

Exactor 50 inch sliding table for table saw. Same as Excalibur and the current Sawstop. Local pick up only Los Angeles area. $375.00 OBO.

see more

1 replies | 794 view(s)
05-09-2023, 6:34 PM

Rob Sack replied to a thread Replacement Kitchen cabinet doors in General Woodworking and Power Tools

I would recommend regular weight MDF over lightweight MDF. The edges on the lightweight MDF are a lot more fragile than regular weight. As far as...

see more

21 replies | 2064 view(s)
05-07-2023, 10:51 PM

Rob Sack replied to a thread 30" X 7ft top glue up in General Woodworking and Power Tools

I did a solid 8/4 walnut dining table top that was 42 x 108 in a single glue up, and that was tough but doable and all the joints were perfect. ...

see more

22 replies | 1504 view(s)
05-07-2023, 10:32 PM

Rob Sack replied to a thread Questions on Performax 22-44 Pro in General Woodworking and Power Tools

I would pass at half the price. I bought that exact machine new directly from Performax. From day one, I never could produce a panel that was truly...

see more

7 replies | 833 view(s)

No More Results

Rob Sack
Contributor

Mini Statistics

Recent Visitors

Basic Information

Statistics

Total Posts

General Information

Rob Sack Contributor

Mini Statistics

Recent Visitors

Basic Information

Statistics

Total Posts

General Information

Rob Sack
Contributor