View Profile: Bob Johnson2 - Sawmill Creek Woodworking Community

Yesterday, 7:11 PM

Bob Johnson2 replied to a thread Jobsite Tablesaw Failings at Furniture in General Woodworking and Power Tools

About 2 months ago I went from a 3 hp Unisaw to a Dewalt dwe7491rs jobsite saw. I obviously don't have a lot of time with the Dewalt but here's my...

11 replies | 289 view(s)

01-26-2021, 11:50 AM

Bob Johnson2 replied to a thread Dado blade set in General Woodworking and Power Tools

I've got a Dadonator, cuts well but the finish, or lack of, on the blades themselves is lacking. Need to keep them waxed or they corrode. This may...

17 replies | 496 view(s)

01-24-2021, 8:08 PM

Bob Johnson2 replied to a thread Two Quick Questions about Miter Gauges in General Woodworking and Power Tools

Left, right. Cause it just works that way.

15 replies | 430 view(s)

01-24-2021, 4:01 PM

Bob Johnson2 replied to a thread Jessum routrlift11 @ $187 vs Jessum mastrlift $389 in General Woodworking and Power Tools

I've had aluminum Jessum rings for ages. Only one, the smallest, had a bit hit it at some point. Being aluminum, like the Incra, it does no...

7 replies | 292 view(s)

01-23-2021, 5:03 PM

Bob Johnson2 replied to a thread Air Quality Monitors in WorkShops

Thanks. I figure to use one the same way, when to put on the respirator and when I can take it off. I see there is a flash deal for $30 for the next...

29 replies | 789 view(s)

01-22-2021, 5:09 PM

Bob Johnson2 replied to a thread Air Quality Monitors in WorkShops

I guess it's not as simple as looking at the numbers on the monitor. I need to do some more homework on this. Thanks all.

29 replies | 789 view(s)

01-22-2021, 1:47 PM

Bob Johnson2 replied to a thread Air Quality Monitors in WorkShops

Glenn, never having used one, do you go by the small particle measurement or the large?

29 replies | 789 view(s)

01-22-2021, 11:50 AM

Bob Johnson2 started a thread Air Quality Monitors in WorkShops

For those with monitors. I'm attempting to improve the air quality in the shop, it's in the basement. I have a 1 stage dust collector with Merv 15...

29 replies | 789 view(s)

01-19-2021, 5:59 PM

Bob Johnson2 replied to a thread Saw Blades in General Woodworking and Power Tools

Thanks for the help folks. I found the 10" Freud Glue line rip blade but it's out of stock everywhere, asked to be notified when it comes in. The...

8 replies | 453 view(s)

01-18-2021, 10:14 PM

Bob Johnson2 started a thread Saw Blades in General Woodworking and Power Tools

A few questions on saw blades. Since getting rid of my cabinet saw and getting a Dewalt job site saw I need to change or add to my blade...

8 replies | 453 view(s)

01-16-2021, 6:08 PM

Bob Johnson2 replied to a thread Dust collection in small shop - Pegboard and preventing dust from collecting behind in WorkShops

I think pegboard without drywall would do the trick. I've got a couple sheets of pegboard up, been there for 40 years and I've yet to worry about...

6 replies | 468 view(s)

01-16-2021, 6:50 AM

Bob Johnson2 replied to a thread Jet 6" Benctop Jointer JJ-6HHBT (718600) in General Woodworking and Power Tools

Appreciate the follow up.

19 replies | 951 view(s)

01-13-2021, 7:52 AM

Bob Johnson2 replied to a thread How do I ensure a straight edge is straight? in General Woodworking and Power Tools

I have a 36" Straightedge, if I need something longer I use a level. When I redid the kitchen cabinets the counter guy had an 8' straightedge, that...

20 replies | 1149 view(s)

01-09-2021, 7:56 PM

Bob Johnson2 replied to a thread Outfeed Table for DeWalt 7491RS Portable Saw Part 1 in Shop Made Tools and Machines

Picked one up about a month ago, here's the "C" in question. Doesn't look to be an issue. Thanks for the plans Dick.

13 replies | 12056 view(s)

01-09-2021, 8:14 AM

Bob Johnson2 replied to a thread TS Recommendation-Grizzly G0869 VS Ridgid R4514 in General Woodworking and Power Tools

Can't see what the fence looks like on the Ridgid and the one on the Griz looks kind of cheesy. If you can swing $600, the Dewalt DWE7491RS is worth...

12 replies | 445 view(s)

01-04-2021, 7:02 PM

Bob Johnson2 replied to a thread Jet 6" Benctop Jointer JJ-6HHBT (718600) in General Woodworking and Power Tools

I would be interested in your impressions when you get it. I like that it's cast iron as opposed to aluminum. Needing to lighten up, as in weight, my...

19 replies | 951 view(s)

Bob Johnson2
Contributor

Mini Statistics

Recent Visitors

Basic Information

About Bob Johnson2

Statistics

Total Posts

General Information

Bob Johnson2 Contributor

Mini Statistics

Recent Visitors

Basic Information

About Bob Johnson2

Statistics

Total Posts

General Information

Bob Johnson2
Contributor