Jimmy Harris
Contributor

I've seen those before. Not in person, mind you. But I think it's just an aesthetic thing. A reason to stand out from all of the other saw makers...

I get them off Amazon. You can get a bunch, dirt cheap, and they're already blunted. Plus they usually come with various diameter tips, so you can...

Most any Baily or Bedrock pattern plane can be made to work well and give consistent and excellent results. The basic design is pretty foolproof. A...

You can also make your own with blocks of wood. Just make sure to elongate one of the holes to allow for expansion. There are lots of ways to...

I've glued up wood that wasn't touched in years before. And it held fine. So long as it hasn't warped, and you didn't put a finish on it, leave it...

Quite true. But it all depends on the situation. I'm not a rich man, so a lot of the furniture I've owned wasn't worth holding onto forever. But...

Thinning PVA glue with water works really well. I do it all of the time for various reasons. Sometimes, to get it through the needle of a syringe. ...

Yeah, I'm not a fan of unnecessary complications. And to me, the systainer stuff is an overly complicated problem, disguised as a solution. It...

I think I will too. It's gonna take a while to get it set up. It's filthy. So I've got to do a deep cleaning. And there's some repairs I need...

I found a 17" Grizzly G0513ANV for a great price and picked it up yesterday (8 hours of driving a U-Haul trailer on back roads was no fun). The...

Anytime I've experienced tearout with my DW735, I just take a smaller bite and it clears up. You can plane against the grain with the stock knives,...

From an engineering standpoint, I can't help but feel you're adding extra complexity, and thus increasing the odds of failure, for very little...

I wouldn't pay it any mind. Epoxy pours are very popular right now, which also means they are very unpopular with a certain population. It's...

I use paraffin wax for pretty much everything. Paraffin is cheap, versatile, easy to find (I get it at the grocery store) and it works. Plus it's...

Founder's grade /ˈfoundərs ɡrād/ adjective 1. a description of a cast metal object of unknown quality 2. an embellishment disguised as a...

$450 for a workbench in 2009 sounds like quite a bargain now!

I'm not seeing a whole lot on the used market. The Laguna LT16 SEC (Meber) and a Mini Max E16 (Centauro) have popped up. Both look to be in really...

I love it! That's kind of what I did for a while. Only I ran 4ft long F clamps across the top of my table, because there isn't a lip underneath. ...

Using new glue, I've had no problems with TB3 in temperatures applied near the bottom of their recommendations, with overnight temps dropping near,...

1. I can't say for sure about the blades. You may want to remove the old blades and take some measurements. But so long as their the same length,...

$30 for all of that? That's crazy! I couldn't buy that much pine for that price!

In my experience, this is every profession. And more important than business savvy, if you want to consider it a separate thing, is networking. I...

I'm sure some still do. But I wouldn't be surprised if most, especially the younger generations, haven't gotten away from that. I know it was...

When glueing end grain to end grain with a PVA glue, it's best to mix up a 50/50 mixture of water and glue and apply that to the end grain. Then...

I've read a lot of people complaining about it failing on them. But personally, I've never had an issue. I used it on some outdoor planters a few...

I'm flexible on budget. It's gonna cost what it costs and I have a bit of money saved up. But I'm not rich, so I every dollar spent towards a...

It's not as bad as it sounds. And no, I'm very skinny (except for my pot belly). You just take lots of little breaks to catch your breath and focus...

A Hock blade and chip breaker would be a worthy upgrade for that plane. So I wouldn't say no to it, since those are things I would probably want to...

Thank you. This also helps out a lot. I think I'm learning what I need to know. And I'm leaning towards a new G0513, depending on what I can...

With all due respect, I think I understand a lot better what you're saying than you understand what I'm saying. And that's perfectly understandable....