View Profile: Mitch schiffer - Sawmill Creek Woodworking Community

Tab Content: All; Mitch schiffer; Friends; Photos

Older Activity
06-27-2022, 10:17 PM

Mitch schiffer started a thread Hydraulic trailer brakes in Off Topic Forum

I just picked up a bigger trailer and I currently has non functional air over hydraulic drum breaks. Im wondering if anyone has experience with the...

see more

9 replies | 295 view(s)
06-16-2022, 10:13 PM

Mitch schiffer replied to a thread Power Feeder on Phenolic Top in General Woodworking and Power Tools

I have a jessem phenolic router table and I have the smallest powermatic poweer feeder on it. I drilled 2 of the holes through the lip on the back...

see more

23 replies | 1592 view(s)
06-16-2022, 10:06 PM

Mitch schiffer replied to a thread Surprise inside in General Woodworking and Power Tools

I see a lot of poplar like that at my local menards. I do buy it occasionally even though it is expensive there. I made some French doors out of...

see more

6 replies | 741 view(s)
06-16-2022, 10:03 PM

Mitch schiffer replied to a thread Which planer to buy in General Woodworking and Power Tools

I had a 20 inch shopfox with a mobile base and it was very easy to move around. The shopfox replaced a jet jpm15 and the Grizzly was replaced by a...

see more

16 replies | 1128 view(s)
06-09-2022, 10:51 PM

Mitch schiffer replied to a thread Buying land now? in Off Topic Forum

I have an update to this if anyone was curious. I did get this under contract. Im buying it on land contract for a 4 year term. Here are a few...

see more

32 replies | 4207 view(s)
06-09-2022, 3:47 PM

Mitch schiffer replied to a thread Stapler vs Framing Nailer in General Woodworking and Power Tools

Some inspectors in my area won't allow staples for sheating. I have never seen them used for framing. I only use nails for sheating.

see more

17 replies | 1416 view(s)
06-07-2022, 7:57 PM

Mitch schiffer replied to a thread Does anyone collect these kind of things in General Woodworking and Power Tools

I have seen lots of these fora sale very cheap on Craigslist and they usually sit on the for a long time. I don't believe there is any value in these...

see more

12 replies | 1322 view(s)
06-03-2022, 9:30 AM

Mitch schiffer replied to a thread Revo K-body problem in General Woodworking and Power Tools

If you have a local bessey dealer that might be better to go though for your warranty. I have never had an issue with my k body clamps however I do...

see more

4 replies | 807 view(s)
06-03-2022, 9:24 AM

Mitch schiffer replied to a thread Jointer recommendations - any G0858 fans? in General Woodworking and Power Tools

I will probably be the minority here but I had the g0858 and I didn't like it. It seems underpowered to me. It is listed as a 3hp but seems to be...

see more

36 replies | 2202 view(s)
06-03-2022, 9:16 AM

Mitch schiffer replied to a thread Battery Platforms (22/36/40V etc.) in General Woodworking and Power Tools

I have quite a few milwaukee m18 tools. I like most of them better then the dewalt flexvolt and the Marita 36volt. The high voltage batteries have a...

see more

34 replies | 1901 view(s)

No More Results

Mitch schiffer
Contributor

Mini Statistics

Recent Visitors

Basic Information

About Mitch schiffer

Statistics

Total Posts

General Information

Mitch schiffer Contributor

Mini Statistics

Recent Visitors

Basic Information

About Mitch schiffer

Statistics

Total Posts

General Information

Mitch schiffer
Contributor