View Profile: Mitch schiffer - Sawmill Creek Woodworking Community

06-30-2022, 8:13 PM

Mitch schiffer replied to a thread Hydraulic trailer brakes in Off Topic Forum

My truck isn't set up for air brakes plus the whole system excluding the breaks them selves are in pretty bad shape.

12 replies | 624 view(s)

06-29-2022, 10:07 PM

Mitch schiffer started a thread Sawstop sliding table in General Woodworking and Power Tools

Has anyone tried the newer heavier duty sliding table from sawstop? I haven't heard much if any about it. I have seen several unfavorable reviews on...

5 replies | 570 view(s)

06-29-2022, 10:04 PM

Mitch schiffer replied to a thread Hydraulic trailer brakes in Off Topic Forum

Is there a big difference in the hydraulic drum vs disk between your 2 trailers?

12 replies | 624 view(s)

06-27-2022, 10:17 PM

Mitch schiffer started a thread Hydraulic trailer brakes in Off Topic Forum

I just picked up a bigger trailer and I currently has non functional air over hydraulic drum breaks. Im wondering if anyone has experience with the...

12 replies | 624 view(s)

06-16-2022, 10:13 PM

Mitch schiffer replied to a thread Power Feeder on Phenolic Top in General Woodworking and Power Tools

I have a jessem phenolic router table and I have the smallest powermatic poweer feeder on it. I drilled 2 of the holes through the lip on the back...

23 replies | 1647 view(s)

06-16-2022, 10:06 PM

Mitch schiffer replied to a thread Surprise inside in General Woodworking and Power Tools

I see a lot of poplar like that at my local menards. I do buy it occasionally even though it is expensive there. I made some French doors out of...

6 replies | 768 view(s)

06-16-2022, 10:03 PM

Mitch schiffer replied to a thread Which planer to buy in General Woodworking and Power Tools

I had a 20 inch shopfox with a mobile base and it was very easy to move around. The shopfox replaced a jet jpm15 and the Grizzly was replaced by a...

16 replies | 1167 view(s)

06-09-2022, 10:51 PM

Mitch schiffer replied to a thread Buying land now? in Off Topic Forum

I have an update to this if anyone was curious. I did get this under contract. Im buying it on land contract for a 4 year term. Here are a few...

32 replies | 4250 view(s)

06-09-2022, 3:47 PM

Mitch schiffer replied to a thread Stapler vs Framing Nailer in General Woodworking and Power Tools

Some inspectors in my area won't allow staples for sheating. I have never seen them used for framing. I only use nails for sheating.

17 replies | 1457 view(s)

06-07-2022, 7:57 PM

Mitch schiffer replied to a thread Does anyone collect these kind of things in General Woodworking and Power Tools

I have seen lots of these fora sale very cheap on Craigslist and they usually sit on the for a long time. I don't believe there is any value in these...

12 replies | 1354 view(s)

06-03-2022, 9:30 AM

Mitch schiffer replied to a thread Revo K-body problem in General Woodworking and Power Tools

If you have a local bessey dealer that might be better to go though for your warranty. I have never had an issue with my k body clamps however I do...

4 replies | 808 view(s)

06-03-2022, 9:24 AM

Mitch schiffer replied to a thread Jointer recommendations - any G0858 fans? in General Woodworking and Power Tools

I will probably be the minority here but I had the g0858 and I didn't like it. It seems underpowered to me. It is listed as a 3hp but seems to be...

38 replies | 2634 view(s)

06-03-2022, 9:16 AM

Mitch schiffer replied to a thread Battery Platforms (22/36/40V etc.) in General Woodworking and Power Tools

I have quite a few milwaukee m18 tools. I like most of them better then the dewalt flexvolt and the Marita 36volt. The high voltage batteries have a...

34 replies | 1935 view(s)

Mitch schiffer
Contributor

Mini Statistics

Recent Visitors

Basic Information

About Mitch schiffer

Statistics

Total Posts

General Information

Mitch schiffer Contributor

Mini Statistics

Recent Visitors

Basic Information

About Mitch schiffer

Statistics

Total Posts

General Information

Mitch schiffer
Contributor