View Profile: BOB OLINGER - Sawmill Creek Woodworking Community

Tab Content: All; BOB OLINGER; Friends; Photos

Older Activity
Today, 12:22 PM

BOB OLINGER started a thread Shutter Slats in SawMill Creek Classifieds

I have about 700 linear ft. of shutter slats, made from poplar, 2 7/8" wide. - about 13 pieces - 7' - about 60 pieces - 5' - about 55 pieces -...

see more

0 replies | 90 view(s)
01-16-2021, 8:45 AM

BOB OLINGER replied to a thread Changing Dust Collector Bag in WorkShops

Is there a set-up to replace the bag? I seem to recall seeing like someone install a clear tube to a receptacle below.

see more

8 replies | 287 view(s)
01-15-2021, 5:00 PM

BOB OLINGER started a thread Changing Dust Collector Bag in WorkShops

I have a Delta 1 1/2 HP dust collector with a Thien separator. Changing the dust collection bag is a pain. I recall other set-up options but can't...

see more

8 replies | 287 view(s)
01-11-2021, 7:24 PM

BOB OLINGER replied to a thread Paint Sprayer Recommendatoin in Project Finishing

Thanks, Jerry. May just toss the sprayer as this is a rough application - not too worried on using the gun again for finish application as I can...

see more

5 replies | 249 view(s)
01-11-2021, 7:20 PM

BOB OLINGER replied to a thread Paint Sprayer Recommendatoin in Project Finishing

George, Thanks for the youtube video. I've never used lacquer like he promotes but will definitely give it a try on a piece of furniture. ...

see more

5 replies | 249 view(s)
01-11-2021, 1:30 PM

BOB OLINGER started a thread Paint Sprayer Recommendatoin in Project Finishing

OK, I likely will spray shellac over studs, joists, and subfloor to seal smoke odor. What is the recommendation for an inexpensive sprayer? ...

see more

5 replies | 249 view(s)
01-06-2021, 6:50 PM

BOB OLINGER started a thread Sealing Smoke Odor in Off Topic Forum

We may have an opportunity to renovate and flip a small house with smoke damage. I picked up a recommendation that said to seal the bare wall studs...

see more

8 replies | 426 view(s)
12-29-2020, 10:15 AM

BOB OLINGER replied to a thread Best drill bit for horizontl boring in Turner's Forum

John, Do you use a bit extension, or have you found Forstner bits with long shanks?

see more

20 replies | 1818 view(s)
12-29-2020, 10:13 AM

BOB OLINGER replied to a thread Best drill bit for horizontl boring in Turner's Forum

Thanks, Alex. Bob O.

see more

20 replies | 1818 view(s)
12-29-2020, 10:12 AM

BOB OLINGER replied to a thread Best drill bit for horizontl boring in Turner's Forum

Thanks, John. Bob O

see more

20 replies | 1818 view(s)
12-29-2020, 10:12 AM

BOB OLINGER replied to a thread Best drill bit for horizontl boring in Turner's Forum

Thanks, David. Bob O

see more

20 replies | 1818 view(s)
12-28-2020, 2:12 PM

BOB OLINGER replied to a thread Best drill bit for horizontl boring in Turner's Forum

Thanks, Reed, yes, I've been clearing about every inch or so. Likely need to slow down a bit. Bob O

see more

20 replies | 1818 view(s)
12-28-2020, 2:11 PM

BOB OLINGER replied to a thread Best drill bit for horizontl boring in Turner's Forum

Thanks, Dan. Bob O

see more

20 replies | 1818 view(s)
12-28-2020, 2:10 PM

BOB OLINGER replied to a thread Best drill bit for horizontl boring in Turner's Forum

Thanks, Cliff \ Bob O

see more

20 replies | 1818 view(s)
12-28-2020, 11:19 AM

BOB OLINGER replied to a thread Best drill bit for horizontl boring in Turner's Forum

Dave, Thanks, I was wondering about using an auger bit. Yes, I should likely slow down a bit. We gave numerous for Christmas and received a lot...

see more

20 replies | 1818 view(s)
12-28-2020, 10:38 AM

BOB OLINGER started a thread Best drill bit for horizontl boring in Turner's Forum

I've just started making pepper mills and getting along pretty good. One of the steps is horizontal boring (on lathe) the hole in the wood stock - 1...

see more

20 replies | 1818 view(s)
12-22-2020, 11:05 AM

BOB OLINGER started a thread Dust Collection -Lathe in Turner's Forum

Can anyone share some good dust collection applications for a full size lathe. I dug my lathe (older Rockwell-Delta) out and have recently turned a...

see more

17 replies | 1596 view(s)

No More Results

BOB OLINGER
Contributor

Mini Statistics

Recent Visitors

Basic Information

About BOB OLINGER

Statistics

Total Posts

General Information

BOB OLINGER Contributor

Mini Statistics

Recent Visitors

Basic Information

About BOB OLINGER

Statistics

Total Posts

General Information

BOB OLINGER
Contributor