Ron Selzer
Contributor

Agree with above I was referring to mode 2 using a different description, however the Leviton 5252, along with I believe Pass & Seymour 5252 and...

IF IT IS THE TYPE THAT THE SCREW TIGHTENS A CLAMP THEN it is the best way, better than side wired Leviton 5252 or equivalent Ron

I agree 100%, you are set up for ripping only on that saw. Find a feeder and go at it. I own a SawStop 5hp ICS and it is very nice if you do decide...

Talk to a real sheet goods supplier about Baltic Birch comes in 60"x60", price by skid, bunk whatever term is uses locally should be 2x sheets in...

CLEAN, CLEAN esp. inside cabinets, no sawdust touch paint up oil/lightly grease any exposed metal wax top with a heavy coat and don't buff it out...

Basement? Run conduit around outside of house, fasten to foundation lower than siding. Bury it in the ground, pvc conduit with no 6 copper wire and...

do it all the time on rough sawn lumber that is worse that what you get out of a bandsaw That 12" jointer should eat that wood, start out with depth...

For what you paid for the POWERMATIC ,I would expect no snipe, at least based on how some people on this board "BRAG" about them. However even back...

somebody will buy the house when it goes on market some will tear the kitchen out and replace all of it some will paint everything in it white or...

Bob, would you please post pictures of the under table dust collection on the bandsaw Thank you Ron

my right side gets used as a staging area alot. then gets cleaned off to move the saw Ron

5hp, ICS, 36" fence, mobile base in 2015. Removed top, motor to make it easier to get in basement. Put it back together by myself while off work...

I have a SawStop ICS 5hp, 36" fence, overarm dust collection and mobile base. Had a 1987 Delta contractors saw, have a few years time on a PM 66...

Renting the pickup is a smart idea The truck driver is ONLY required to get the crate to the back of the truck UNLESS lift gate services have been...

pm sent .............

You keep saying you want to crosscut plywood take a look at https://safetyspeed.com/product-category/vertical-panel-saws/ American made I have a...

NO, I think, could be wrong the ones by the guy on the east coast with the Martins in his basement that he rebuilt were longer

add a gravity damper to an outside wall so that if the area goes negative then it opens as much as needed to make the air up. too much exhaust not to...

I always seem to be the happiest with Forrest Freud is good just not as good Ron

I recommended an oversize heater based on OP stated requirements, not what I have or prefer "My heating requirements are as follows: The shop will...

sealed burner, vented propane oversized to twice normal as you want to quickly bring the space up to comfort. 2 heaters or one variable rate of fire....

Started years ago using incandescent 300w lamps (3) mixed in with fluorescent lamps (12) to get the color I like along with the lighting level I...

Very easy to do, scan original check print a duplicate copy that is presented to seller. seller calls bank verifies check is good AT THAT TIME,...

according to quite a few posts over on a farm equipment board cashier checks are very easy way to cheat someone. local long time equipment auction...

like that infeed table design, might copy it Ron

my house is a tract ranch home built 1999 stairs is a straight shot down to the basement. I was at work when the sander got moved down by local...

mobile base will make a big saw fit in a small space. Have a 5hp SawStop ICS 36" with mobile base. Constantly jacking the saw up and turning or...

yes it makes it easier practice, practice and practice works best for this job

1/2" copper run lines where you want install a drip leg at each outlet OR Rapid air , have read good things about it DO NOT INSATLL pvc lines for...

Plane arrived today, very well packed, better condition than described Ron