View Profile: Steve Jenkins - Sawmill Creek Woodworking Community

05-21-2022, 7:54 PM

Steve Jenkins replied to a thread I think my zero turn mower is cursed! in Off Topic Forum

If voltage was an issue why would it start just fine after a light tap on the starter? The positive on the starter goes direct to the battery with...

32 replies | 982 view(s)

05-21-2022, 6:41 PM

Steve Jenkins replied to a thread I think my zero turn mower is cursed! in Off Topic Forum

I have two Kubotas that acted like that. The service tech put a relay between the battery and the starter solinoid To provide full power. Solved the...

32 replies | 982 view(s)

05-18-2022, 5:33 PM

Steve Jenkins replied to a thread Cost effectiveness of a slider vs. tracksaw & tablesaw in General Woodworking and Power Tools

Of long ago using a slider I broke down 23 sheets of ply in about an hour and a half. It was for a wall of lockers with drawers below. Did not...

32 replies | 2361 view(s)

05-18-2022, 1:40 PM

Steve Jenkins replied to a thread Looking for some help in Amarillo in SawMill Creek Classifieds

Thanks John. I passed on trying to make the thresholds but got a lot of other stuff done. Taught Suzanne how to use a mitre saw and nail gun and she...

4 replies | 695 view(s)

05-13-2022, 6:53 PM

Steve Jenkins replied to a thread Looking for some help in Amarillo in SawMill Creek Classifieds

Thanks for the assist offer Malcom. Don’t think I can make it work though.

4 replies | 695 view(s)

05-13-2022, 4:39 PM

Steve Jenkins started a thread Looking for some help in Amarillo in SawMill Creek Classifieds

I’m in Amarillo for the weekend working on my stepdaughter’s house. i need to make two thresholds from red oak. Anyone with a planer or bandsaw...

4 replies | 695 view(s)

05-11-2022, 5:39 PM

Steve Jenkins replied to a thread How can I use a rotary laser level with a building in the way? in Off Topic Forum

If you use a really long grade pole make sure it’s vertical. If it is tilted either away or towards the laser it can throw you off by inches.

16 replies | 1464 view(s)

05-10-2022, 1:54 PM

Steve Jenkins replied to a thread Blush in post-cat varnish in Project Finishing

If it’s kemvar it’s gonna be tough. Typically for blush you can mist spray the solvent for the finish and it will soften it slightly and let the...

2 replies | 457 view(s)

05-06-2022, 5:03 PM

Steve Jenkins replied to a thread Router Help Needed in General Woodworking and Power Tools

When I have a stuck bit I use the edge of the collett wrench and tap the shank of the bit. Make sure your collett is actually loose. Many loosen then...

14 replies | 1006 view(s)

05-03-2022, 6:25 AM

Steve Jenkins replied to a thread parts for Kremlin - where to buy? in Project Finishing

I get mine from Woodfinisher’sdepot.com. Also get the conversion varnish there that I use.

3 replies | 657 view(s)

04-30-2022, 9:28 AM

Steve Jenkins replied to a thread Hammer A3-31 Infeed table issue in General Woodworking and Power Tools

To see pictures you must become a contributor which is only six bucks a year. There is a donate button near the top of the page. There are a couple...

21 replies | 1318 view(s)

04-27-2022, 8:35 PM

Steve Jenkins replied to a thread Hammer A3-31 Infeed table issue in General Woodworking and Power Tools

Where are you located? Someone may be close enough to give you a hand. I know I enjoy doing that.

21 replies | 1318 view(s)

Steve Jenkins
Contributor

Mini Statistics

More 2 Friends

Jim Rimmer

Adrian Anguiano

Recent Visitors

1 Visitor Messages

Basic Information

About Steve Jenkins

Signature

Statistics

Total Posts

Visitor Messages

General Information

2 Friends

Adrian Anguiano

Jim Rimmer

Steve Jenkins Contributor

Mini Statistics

More 2 Friends

Jim Rimmer

Adrian Anguiano

Recent Visitors

1 Visitor Messages

Basic Information

About Steve Jenkins

Signature

Statistics

Total Posts

Visitor Messages

General Information

2 Friends

Adrian Anguiano

Jim Rimmer

Steve Jenkins
Contributor