View Profile: Steve Jenkins - Sawmill Creek Woodworking Community

Tab Content: All; Steve Jenkins; Friends; Photos

Older Activity
Today, 5:30 PM

Steve Jenkins replied to a thread New Router Station - Quick Review of some Rockler Products in WorkShops

Very nice. Looks like it will work well

see more

1 replies | 61 view(s)
08-04-2022, 3:01 PM

Steve Jenkins replied to a thread losing my mind over sanding swirls in General Woodworking and Power Tools

I agree with Patrick about using a pencil to draw a light cross hatch pattern and sand until it’s gone. Do that every grit. Clean thoroughly between...

see more

31 replies | 1686 view(s)
07-30-2022, 4:01 PM

Steve Jenkins replied to a thread Pattern cutting end grain in General Woodworking and Power Tools

You’ll have better luck with a spiral cutter but even better would be a disc sander or stationary belt sander

see more

13 replies | 808 view(s)
07-29-2022, 12:21 PM

Steve Jenkins replied to a thread How do you remove this sprocket in General Woodworking and Power Tools

Is it possible that what the motor mounts to can move but is stuck.

see more

49 replies | 3777 view(s)
07-29-2022, 11:29 AM

Steve Jenkins replied to a thread Source for hardwood panels? in General Woodworking and Power Tools

Did a quick search and came up with advantagelumber.com

see more

7 replies | 504 view(s)
07-29-2022, 11:19 AM

Steve Jenkins replied to a thread How do you remove this sprocket in General Woodworking and Power Tools

Take a closer look at the tightening bolt and see if there is an idler sprocket that it pushes against. The shaft for it may be stuck and a light tap...

see more

49 replies | 3777 view(s)
07-28-2022, 3:51 PM

Steve Jenkins replied to a thread How do you remove this sprocket in General Woodworking and Power Tools

Look along the length of the chain and you may find what looks like a piece of stiff wire pressing the slack out of the chain. Loosen the bolt...

see more

49 replies | 3777 view(s)
07-27-2022, 4:07 PM

Steve Jenkins replied to a thread Shaper selection in General Woodworking and Power Tools

I have a Gomad tilting spindle with sliding table similar to the pic in the previous post. If you look at the pic you can see a handle just above and...

see more

47 replies | 3395 view(s)
07-26-2022, 1:10 PM

Steve Jenkins replied to a thread Heading to Bellingham WA. in Off Topic Forum

I stop by Grizzly every time I go. Another must see is the Spark Museum of Electrical Invention.

see more

6 replies | 741 view(s)
07-24-2022, 12:41 PM

Steve Jenkins replied to a thread Heading to Bellingham WA. in Off Topic Forum

That’s right. I’ll pm you when it’s closer and you can send me address and phone number. Looking forward to meeting in person and seeing your shop.

see more

6 replies | 741 view(s)
07-24-2022, 9:56 AM

Steve Jenkins replied to a thread Heading to Bellingham WA. in Off Topic Forum

Bill, I’ll be flying into Seattle and my brother picking me up there about noon on the 22nd. If you won’t be at work (I know some people still do...

see more

6 replies | 741 view(s)
07-22-2022, 11:23 AM

Steve Jenkins replied to a thread "Unboxing" - Harvey G700 DC in WorkShops

That’s really a nice looking unit

see more

26 replies | 3162 view(s)

No More Results

Steve Jenkins
Contributor

Mini Statistics

More 2 Friends

Jim Rimmer

Adrian Anguiano

Recent Visitors

1 Visitor Messages

Basic Information

About Steve Jenkins

Signature

Statistics

Total Posts

Visitor Messages

General Information

2 Friends

Adrian Anguiano

Jim Rimmer

Steve Jenkins Contributor

Mini Statistics

More 2 Friends

Jim Rimmer

Adrian Anguiano

Recent Visitors

1 Visitor Messages

Basic Information

About Steve Jenkins

Signature

Statistics

Total Posts

Visitor Messages

General Information

2 Friends

Adrian Anguiano

Jim Rimmer

Steve Jenkins
Contributor