Edward Weber
Contributor

That sounds exactly how I make mine. Good and snug, which usually requires a mallet for final seating. I like to treat all joints pretty much the...

Speaking only for myself, To avoid what you mention, I chamfer the four corners of the tenon very slightly. This allows for glue and/or air to have...

A slightly different view In my work, joinery should be a tight, well fitted union of the wood components. In most cases, adhesive is there as a...

I use the Freud Thin Kerf Sliding Compound Miter Saw Blade on my RAS and SCMS https://www.freudtools.com/products/LU91M010 They are less aggressive...

I thought that the AI was going to replace us lowly humans. Now it seems that us carbon based life forms need to fact check the work of the AI. ...

Different fuels use different levels and formulations of detergents. These can cause deposits that clog injectors. If a "reputable" garage, like a...

Yep, that's all you need to do

If you buy good fuel and the car runs fine, as you say, you can probably wait until 60k or so. If you put in cheap fuel and your car doesn't run...

I heard that it was citing cases that didn't exist. Maybe it looked through the 20+ years of Law & Order TV show and found some, who knows. Not...

I find these results to be underwhelming. All I can glean is that the AI searched the web, instead of me doing it. The difference is, I can discern...

You could always use velcro or magnets Just a suggestion

That was 10 years ago, nothing has been decided. Call things what you want, just don't expect anyone else to call them the same as you.

https://www.ibctools.ca/about/

I think the point is getting lost a bit. It's not that .005" matters or not, or if it's close enough for most people, or don't worry about it,...

IMO, I think you need to pump the brakes and rethink what you're after. You want to bore some a 2+" deep hole into some sheet goods, far from the...

How precision a hole? What size hole? How far into the center, 24"? Could you use a plunge router?

Well there you go, a typical situation of who's right or who's not. In my shop there are vessels, jars, boxes and containers. They are what I say...

We always drill the re-bar for aprons, walks, patios, and landings into the building. The assumption is that there is going to be settling around...

Forgive me if this seems harsh but why are you looking at these tools for woodworking? There are tools better suited for the task. There are plenty...

Thats the way I was trained to do a landing like that. If there is concern about settling, we use poured piers rather than driving rods. How to get...

Eric, I somewhat agree with your point but at the end of the day, as they say, it's his business and he should know what's going on. The customer...

I have had a similar experience buying turning tools, 3 different times from two different sellers. This was over a 1-2 year period of time about 8...

It only matters if you are trying to understand what other people are talking about. I agree that everyone can interpret things in their own way but...

No, you're ot the jerk, you're the customer. If they can't provide what they advertise and are unwilling to work with you, their loss. take your...

As some of us mentioned, the only issue is the solar cell getting cloudy after a few years of continuous exposure. Cheap ones only seem to last a...

Unstiched buffing wheels are easy to find, you'll just need to find some center flanges that fit your 3/8" arbor. This might help

I know what powder post beetle larva look like and recognize their work. I have them working away in some Red Oak 6 X 6's :mad:. 4 coats of copper...

One of my clients passes along his Air Force Magazines. It is interesting to see that they have become Air & Space Force magazines. Thinking about...

I need to have the bottom flat and true so the boards lay in the bed of clamps without any rocking. Then I work on the edges, putting the bottom...