View Profile: ChrisA Edwards - Sawmill Creek Woodworking Community

08-06-2022, 2:57 PM

ChrisA Edwards replied to a thread Seeking Advice for large used purchase in Off Topic Forum

This one is just over a year old. One owner that only used it a handful of times, but spending some time with him on Thursday, he seems the real...

19 replies | 1225 view(s)

08-06-2022, 12:09 PM

ChrisA Edwards replied to a thread Seeking Advice for large used purchase in Off Topic Forum

I met the seller in VA at a campground. We setup the RV, went through all the features to make sure everything worked. We then went to Bank Of...

19 replies | 1225 view(s)

08-06-2022, 11:47 AM

ChrisA Edwards replied to a thread Dog Attack in Off Topic Forum

My "Stayed in a Holiday Inn" approach would be to try and surrender my left forearm as bait for the dog to lock on to. Then with my right hand go for...

31 replies | 1024 view(s)

08-03-2022, 9:57 PM

ChrisA Edwards replied to a thread Diesel Gas Card in Off Topic Forum

Today I filled up at a truck stop in VA, that was an experience. Lined up with about 10 other tractor trailers. I watched the truck, in front of...

9 replies | 464 view(s)

08-03-2022, 9:25 AM

ChrisA Edwards replied to a thread Diesel Gas Card in Off Topic Forum

Right now it's just diesel, but they are supposedly going to offer this for gas in late 2022 according to their YT videos.

9 replies | 464 view(s)

08-02-2022, 4:57 PM

ChrisA Edwards replied to a thread Diesel Gas Card in Off Topic Forum

For Kev, here's a snapshot of my transaction. I can't make the math fully work between the 5% and 10% stated on the transaction.

9 replies | 464 view(s)

08-02-2022, 2:46 PM

ChrisA Edwards started a thread Diesel Gas Card in Off Topic Forum

Admins, if this inappropriate, please delete. So tomorrow, I pick up a used 5th Wheel Trailer. As part of this new adventure, for us, I also...

9 replies | 464 view(s)

08-02-2022, 10:39 AM

ChrisA Edwards replied to a thread 14" bandsaw, or can I get by with chainsaw for turning in Turner's Forum

Scott, I have a Laguna 14/12 bandsaw with a 3/4" Resaw King blade. For rough shaping, I prefer to be outside with a chainsaw. I went all electric...

26 replies | 1398 view(s)

08-01-2022, 8:37 PM

ChrisA Edwards replied to a thread 14" bandsaw, or can I get by with chainsaw for turning in Turner's Forum

Scott, is this you from the Ducati club?

26 replies | 1398 view(s)

07-27-2022, 1:30 PM

ChrisA Edwards replied to a thread Shaper selection in General Woodworking and Power Tools

Cutting the chamfer

47 replies | 2793 view(s)

07-27-2022, 1:29 PM

ChrisA Edwards replied to a thread Shaper selection in General Woodworking and Power Tools

For hobby use, I decided on the Hammer F3, 1/25" spindle, sliding table and tilting spindle, forward and backward(reversible) motor, pretty much the...

47 replies | 2793 view(s)

07-26-2022, 10:44 PM

ChrisA Edwards replied to a thread Seeking Advice for large used purchase in Off Topic Forum

Chatted again with the seller again lat this afternoon. He texted me photo's of the Title Document(Front and Rear) as well as his driving...

19 replies | 1225 view(s)

07-26-2022, 3:02 PM

ChrisA Edwards replied to a thread Seeking Advice for large used purchase in Off Topic Forum

Popped down to my local DMV Registration office to see if they, here in TN, had any particular requirements about forms and documents needed when...

19 replies | 1225 view(s)

07-26-2022, 10:19 AM

ChrisA Edwards started a thread Seeking Advice for large used purchase in Off Topic Forum

In about a week, I plan to buy a used RV from a private seller. The seller has told me there is no lean or financing on the RV. The seller...

19 replies | 1225 view(s)

07-20-2022, 8:41 AM

ChrisA Edwards replied to a thread Another "which one?" question in CNC Machines

The Onefinity Facebook group https://www.facebook.com/onefinitycnc/photos/p.406505730895571/406505730895571 is a great place for information and...

60 replies | 7417 view(s)

07-19-2022, 11:58 AM

ChrisA Edwards replied to a thread Consistent Domino Problem. Help! in General Woodworking and Power Tools

I think I had similar issues. I made myself a little clamping jig that attaches to the miter slot on my tablesaw. I reference all my Domino cuts...

39 replies | 2722 view(s)

07-17-2022, 10:48 AM

ChrisA Edwards replied to a thread Another "which one?" question in CNC Machines

Thanks, that's exactly what i'm after.

60 replies | 7417 view(s)

07-16-2022, 10:26 PM

ChrisA Edwards replied to a thread Another "which one?" question in CNC Machines

Can you guys post a link to the flow meter please.

60 replies | 7417 view(s)

07-15-2022, 1:29 PM

ChrisA Edwards replied to a thread Another "which one?" question in CNC Machines

I have the same spindle as Alex on my Onefinity. It's extremely quiet while spinning at 10K-18K rpm, nothing like any on my traditional Festool,...

60 replies | 7417 view(s)

07-11-2022, 8:13 PM

ChrisA Edwards replied to a thread Induction Cookware in Off Topic Forum

Le Creuset, the wife's choice and she loves it.

12 replies | 1101 view(s)

ChrisA Edwards
Contributor

Mini Statistics

More 1 Friend

Allen Mattsen

Recent Visitors

2 Visitor Messages

Basic Information

About ChrisA Edwards

Statistics

Total Posts

Visitor Messages

General Information

1 Friend

Allen Mattsen

ChrisA Edwards Contributor

Mini Statistics

More 1 Friend

Allen Mattsen

Recent Visitors

2 Visitor Messages

Basic Information

About ChrisA Edwards

Statistics

Total Posts

Visitor Messages

General Information

1 Friend

Allen Mattsen

ChrisA Edwards
Contributor