ChrisA Edwards
Contributor

I'm still new to turning and so only have accumulated about 10 chisels and a couple of chucks, faceplates etc.. But my lathe tool storage had to...

I fired the safety brake for the first time yesterday in five years of ownership. This was a Dado brake cartridge. I'd installed it and...

I use this one Imperial version https://www.blocklayer.com/woodturning-segmentseng.aspx Metric Version...

My compromise to a slider, that I'd love to own, to perform this task.

I have the floor standing PM719T mortiser, but a couple of months ago, bought the Pantorouter. I've done mortises in fine furniture, box joints...

Thank You, much appreciated. Now I'll have a go at sharpening it.

I have had a couple of homemade goes at this and recently bought the new Woodpeckers drill press fence. I already had their early version of the...

And yet, we have no idea, for members of this forum, what part of the world you reside from your profile

I go backwards and forwards on the idea of the mats, so instead I prefer good shoes/boots. The comfort is there for each foot all the time,...

Sure and in that mode you could add the long extension on both the infeed and outfeed giving you a lot of extra support should you need it. This...

I've had a Harbor Freight, 25' air hose reel, that is about 20+ years old. It's been mounted to the garage ceiling in about 5 different garages. ...

One thought on your ramp, quite often the hardest piece is going over the peak, at the top of the ramp, where the ramp meets the upper floor/surface....

On my A3-31, if I don't tighten the clamping handle on the planer table, while planing, I will get snipe. Other than that, I make shallow planing...

I posted a similar thread about 3 weeks ago. I ended up with a Freud 10" x 80T Thin Kerf Ultimate Plywood & Melamine Blade (LU79R010). ...

The wife let me buy a new shed a couple of years ago, but wasn't happy, so I painted this on it. Sherman Williams paint, the white and blue, the shed...

I had my 19-38 on the OEM stand and it rolled around horribly, had mind of its own as to where it wanted to go. I built a simple cabinet, on...

Bruce, send them to me, I'll pay shipping. Glad to take them off your hands.

https://www.youtube.com/watch?v=2l5DFlCRGKo

Much appreciated. I know it's not a popular thing to admit, but I'm a big Phil Collins and Genesis fan, although I was a fan long before Peter...

I have the Forrest Thin Kerf 20T 10" rip blade ($105). I use it on my Sawstop 3Hp and love it. ...

If you are working on fairly small pieces, you can do M&T joints using a Shaper Origin and their workstation. The workstation provides for...

I have a 3HP Sawstop and use a Forrest Woodworker II thin kerf rip blade. I also bought a thin kerf riving knife from Sawstop directly. It's hard to...

If I'm doing very thin strips, I'll usually cut the strip to the left side of the blade. Once you've dimensioned the piece, you are cutting the...

I've had no issues with passing anything over the saw or on the outfeed table. If I can lift it, the outfeed table can more than support it. My...

Yes, the camera I show in the video, the one I bought, is a 3.6mm lens. https://www.amazon.com/dp/B00T00X1FC/ref=dp_iou_view_product?ie=UTF8&psc=1

I use your block method also. I set the fence and block to cut the deepest part, length, of the tenon and then with each subsequent pass I'm...

Marcus, I have a 36" 3HP Sawstop with the Incra fence system. Prior to installing the Incra fence, at my old house, I had the OEM Sawstop fence...

I switched out most of my fittings to Prevost Hi-Flow (Green), a couple of years ago, and love them. They don't leak and are so easy to...