View Profile: George Yetka - Sawmill Creek Woodworking Community

03-03-2021, 4:40 PM

George Yetka replied to a thread Plywood or solid in General Woodworking and Power Tools

Plywood, An rv will change elevations and moisture levels often if its used. I figure it will be finished but ply will be more stable

11 replies | 529 view(s)

03-03-2021, 4:28 PM

George Yetka replied to a thread amp draw meter in WorkShops

I think the idea of that device is to monitor your money going down the drain amp draw isnt as important in that regard

19 replies | 498 view(s)

03-03-2021, 3:55 PM

George Yetka replied to a thread Hammer A3-41A Jointer - It’s Alive in General Woodworking and Power Tools

Still kicking myself for getting the 31 over the 41. At the time it was $1,000 difference. Only thing i have to say is make sure you keep planer...

6 replies | 521 view(s)

03-03-2021, 3:51 PM

George Yetka replied to a thread amp draw meter in WorkShops

Malcolm I believe that measures KW usage. A clamp meter can show you amp usage while the tool is running but you would need to clamp each hot lead...

19 replies | 498 view(s)

03-03-2021, 9:33 AM

George Yetka replied to a thread Mice in Off Topic Forum

youtube mouse traps. you'll get a lot of bucket traps which seam very effective and you can make them humane or inhumane depending on your...

22 replies | 695 view(s)

03-01-2021, 5:52 PM

George Yetka replied to a thread Water Heater Timer in Off Topic Forum

Havent calculated the savings but we keep house at 68 and raise to 72 5-10 pm and 6-8 am. Temps are a little high for me but have little kids. all of...

13 replies | 483 view(s)

02-26-2021, 3:55 PM

George Yetka replied to a thread Ideas for cutting heavy steel pipe under water? in Off Topic Forum

Do you have a picture?

20 replies | 919 view(s)

02-26-2021, 3:53 PM

George Yetka replied to a thread My First Project using my new woodshop setup. in Woodworking Projects

I've made a load of cutting boards 60+. And people always say they dont want to use it, especially family. Please use it, using a nice hardwood...

8 replies | 398 view(s)

02-26-2021, 12:42 PM

George Yetka replied to a thread My First Project using my new woodshop setup. in Woodworking Projects

Looks Good. What was your finish?

8 replies | 398 view(s)

02-26-2021, 12:14 PM

George Yetka replied to a thread Goto place for lumber in NJ?? in General Woodworking and Power Tools

Boards and beams is pretty good for in NJ. Their prices are not too bad. If you spend 1500 or so they will give you contractor discount. I really...

22 replies | 746 view(s)

02-26-2021, 12:07 PM

George Yetka replied to a thread Ideas for cutting heavy steel pipe under water? in Off Topic Forum

My guess is that it isnt steel, probably cast, Steel would have rusted out pretty quick. I would use a ratcheting snap cutter if it is in fact Cast...

20 replies | 919 view(s)

02-25-2021, 2:50 PM

George Yetka replied to a thread Hivemind, suggestions for fire-rated safes? in Off Topic Forum

I would look at safety deposit box. If you are looking for absolute protection, I dont think that can be had for under 500. If fire is your...

12 replies | 406 view(s)

02-24-2021, 3:39 PM

George Yetka replied to a thread Probably a stupid question... in Off Topic Forum

the other problem is some of these breaks are before the valve. Most codes call for underground pipe to be buried below the frost line but a...

49 replies | 2124 view(s)

02-22-2021, 1:18 PM

George Yetka replied to a thread Traction Cleats for Walking on Icy Roads in Off Topic Forum

I bought the Yaktraks a few years back for a winter trip to yellowstone. They broke a couple hundred feet in. I was able to replace them in the park....

12 replies | 402 view(s)

02-22-2021, 1:07 PM

George Yetka replied to a thread What are your other hobbies besides Woodworking? in Off Topic Forum

-Shooting/reloading mostly pistol lately but some long range -Fountain pens -photography(wish i had more time for this one) With kids and work...

93 replies | 6637 view(s)

02-22-2021, 12:55 PM

George Yetka replied to a thread Preparing brand new Veritas pmv 11 chisels first time in Neanderthal Haven

Out of the 5 I got I lapped all of them from 1000-10000. It took minimal effort but they werent dead flat at least the 1&3/4 were not. They were...

11 replies | 683 view(s)

02-22-2021, 9:36 AM

George Yetka replied to a thread What's your oldest woodworking machine? in General Woodworking and Power Tools

My sawstop dates back to 2016 My fathers tools which were all from the 80's were gifted to my grandfather because he had the time to use them....

53 replies | 2218 view(s)

02-22-2021, 8:54 AM

George Yetka replied to a thread Looking for a way to sand inside a cutting board handle with power tools in General Woodworking and Power Tools

When i do the handles I usually hit it in 4 increments the final increment only being the last 2% or so it should eliminate burning. And for...

18 replies | 643 view(s)

02-20-2021, 12:12 PM

George Yetka replied to a thread Build a router table cabinet from scratch or start with a shop stand? in General Woodworking and Power Tools

I kind of did both. Jessems stand has slots for 1/2" ply. I added a box to house the router a couple of drawers and a door up front to access router...

20 replies | 1199 view(s)

02-18-2021, 2:06 PM

George Yetka replied to a thread Festool RO 125 or 150? in General Woodworking and Power Tools

Ive only been using rotex up to 120 then switching to standard at 120 then progressing. I recently picked up a mirka 5/6 combo but havent put the...

56 replies | 3584 view(s)

02-15-2021, 8:27 AM

George Yetka posted a visitor message on George Yetka's profile

Usps 92055901755477000339539200

02-10-2021, 1:19 PM