David Weaver
Guest

Forrest is as good as anything. Dados are easily chipped from sloppy handling . You can protect them AND make them easier to use by making a box...

For that piece I would use high gloss paint. Its pretty hard to make white too shiney. And I don't think IKEA makes glossy stuff.

That tool is pretty narrow. If you can't find a clear line between steel and iron then the steel is just used up and the piece should just be...

"Warranted cast steel " was a real thing. Small batches were required to make it . Steel making is different now ,but cast steel is still good...

Aye Too ! And the descriptions use the proper gnomenklature !

Yes, And an impluvium can be a big improvium. Saving money on water and roofing

Yeah. It's just more difficult to do a champher than a 90 degree cut. A little lateral movement doing an ordinary 90 doesnt botch the squareness....

I used a 3/4" end mill then finished it with a 3/4" Fisch brad point bit. Don't forget to have something underneath to prevent the hole from blowing...

I tolerate hot better than cold and gloomy. This winter has been real dark so I recently bought one of those lights that you use in the morning to...

Sometimes it's just a crooked band. Bad weld. With the machine off ,I would open the cover and turn the wheel by hand and watch .

awesome Chris! Love how you went "full boat" to inlay individual strip of curly maple to represent the Sun's rays. I admire your high standards! I...

I ordered the 36" DP Pro Fence, Stops, and Base in June. The expected delivery date was September, then middle of November, then middle of December,...

Some furniture stores have ...or used to have their own shops that sold only copies of old pieces of merit. To make the stuff more "authenticky"...

Scott, Sommerfeld tools carries bit sets the profile bit does a slight round over on the edges of the grooves. I’ve never used one, but thought it...

In reading grain to see in what direction the stock should be run ,many will look only at the growth rings....and sometimes that's all you can see....

I agree that's often the case. But I think it's more what cutters are commonly used . Shaper guys often have more steel knives than carbide. Few...

I think it only makes sense when the wood is not dry. And sometimes it doesn't even make sense then, as I have seen wood change color so drastically...

I see no value in multiple passes ,it can work ,but is certainly not reliable. Two passes take twice as long as one pass. Climb cuts work but...

It would be easier to get the right solution if we knew how it was to be used. If the strips will need to be bent, you will have to specify...

Sometime used office furniture places have good chairs. I've got one that has a lot of adjustments, the kind you see in old movies. One foot...

If your profile cutter(s) takes a full height cut you can eliminate tearout by overcutting 1/16" or so- if you want to end up with 2 1/4" width start...

Agree with "soft" maple, used it for mine. Can't remember right now if 6/4 or 8/4 ,but I know I bought it from the vendor around here, they don't...

Is it kiln dried? Would not do the pictured glue-up without kiln dried.

All interesting comments! But bright colors predominated for a long time. Electric lights made it possible to to use dark colors on walls. A good...

I guess new paint is good. But if you listen to real estate people ,yeah, they always mention "neutral colors". What that really means is "you are...

I would not run climb cut with the real profile cutter. But a climb cut made on the still square stock that rounds the corners ,and more if...

My Gramma had an 1890 brownstone with several pocket doors. They ran on brass floor level tracks. Smoooth ...

Agree with Bill, I'd let the vertical edges hang about a half inch lower than the bottom of the top surface. And if the top hangs over all around...

Mel, saw you were a pattern shop guy. I have worked in foundries, (facilities/plant engineering) you guys were definitely well respected, lots of...

I just remembered that in an employment of at least 8 years ,there was a jointer with a spring joint gizmo . But management had told everyone to...