Michael J Evans
Contributor

Hi Ray If I still lived in Springfield, I'd let you try a few different of my stanleys. I'm no expert like these guys, but my very first plane was...

I like that Tom. Thanks for sharing. I have a vintage hammer with two plastic faces, but the plastic is extremely hard clear ( like on the old...

On the other hand, I doubt that I've lost more than a few thousand in sales over 20 years in the business because I don't have a monster table. I...

I agree I got a few 36" of granite cut off and neither of them were flat. Both convex as well. I had a piece of float glass cut which was flat,...

Agree I built my Nicholson style bench for around $180 all in including my holdfasts from eBay and used that for a couple of months before I got a...

You could try the local approach. Google: hose shops near me. As far as the fitting the hose places may have them, or try a hvac / mechanical...

Paul sellers rag in a can / Johnson's paste wax for machinery surfaces and or storage application

Ben I hate you! I still haven't been able to get the compound dovetails looking nice since my last thread on it. Very good job.

Well I'll be doing two more later this week. Both my attempts today / yesterday needed up being two loose. I'm thinking my problem may be I tried...

Derek How come you pictures cannot be clicked on / zoomed in on? I generally view from Mobile and can click on each picture to enlarge it, but yours...

Bob I did a little research and it is on Amazon but unavailable. It is being sold by Taytools. I went directly to Taytools website and it is also...

I'm on my fourth official half blind dovetail and it was another one one those things where I watched some videos and thought "that ain't so bad"....

I have one similar but haven't been able to master adjusting it yet. Ones side is always to high or low.

Rob I picked up one recently on the recommendation of a antique store owner. There is no comparison between the stanley and my cheapo empire...

I really like that Steven. Good use of excess wood and functional

Those are some nice finds Jim. Had no idea baileys didn't have a lateral lever at one point.

With Trotec the terminology is Hertz for frequency. You might, for example, use your lowest Hz setting to perforate paper instead of cutting it. ...

I was down 28% from 2019. All of it covid 19 related.

Oh and with flare fittings you do not need pipe sealant or tape. Just hand tight & a 1/4 turn of the wrench.

Stan, Attached is a picture of some 3/4" pipe, from a old 3/4" pipe clamp in my shop... It measures 3/4"... You are correct in that pipe is...

Bruce, Is this a fitting for flexible tubing or rigid pipe you need? The convoluted flexible tubing known as CSST has its own special sized...

Looking good Derek & thank you for all the photos and directions. Must've taken all day to make that post.

Try Photovac https://photovaclaser.com/general/iradion-laser-update-to-all-our-valued-customers/ They rebuilt a 45 watt Coherent for me several...

I must've been good this year, as santa brought me something I've been dreaming about a long time. A new bandsaw!!!!! A Jet jwbs-14sfx. Seriously...

I sell filters, lubricators, regulators, etc. There are dessicant dryers where you can buy just replacement beads.

The good old dollar tree has varieties of mats for.... $1 I just picked up what is supposed to be a entry way mat ( I think) it's only like 24"l x...

I'd recommend a standard filter and a dessicant dryer. You can also purchase filters that go right before the tool, but I believe those are more so...

Bert I'm not sure either but it looks like there should be 4 "c" parts instead of two. A and B interlock forming an X then the C parts insert as...

I have ceramic tile kitchen countertops and had to cut away some tile to make room for our new range. I used the $40, 4.5" dry tile saw from...