View Profile: Greg Quenneville - Sawmill Creek Woodworking Community

Yesterday, 4:54 PM

Greg Quenneville replied to a thread Options for Harvey Table Saw? in General Woodworking and Power Tools

Plus the outrigger and long fence can be quickly detached when not doing a sheet goods project. And a slider can be fitted with a shop made Fritz &...

34 replies | 1456 view(s)

05-20-2022, 10:04 PM

Greg Quenneville replied to a thread Miter Saw Vertical Cuts not Square in General Woodworking and Power Tools

Just to clarify- if you cut a board laying flat on the saw using the sliding function, and inspect carefully, do you see the same bevel on the cut?

26 replies | 1260 view(s)

05-14-2022, 5:50 AM

Greg Quenneville replied to a thread Using 80/20 on your workbench... in General Woodworking and Power Tools

I mounted some scraps of 80/20 at each end of my bench. They are very handy for storing track saw clamps upside down. The also make a handy cleat for...

4 replies | 917 view(s)

05-11-2022, 6:24 PM

Greg Quenneville replied to a thread Bosch GCM12SD problem in General Woodworking and Power Tools

Regarding the Festool, there are a couple of models wearing the Kapex name. The KS 120 is a very good saw. I built a large period house with...

17 replies | 1620 view(s)

05-10-2022, 10:14 PM

Greg Quenneville replied to a thread Rewiring 220V Bosch GBS 75 AE belt sander to run on 120V power in General Woodworking and Power Tools

If its 220v only is it made for the 50 Hz market? I see that it has an electronic speed control…will that complicate things?

6 replies | 627 view(s)

05-09-2022, 6:37 PM

Greg Quenneville replied to a thread Seeking VFD Advice in General Woodworking and Power Tools

I am not qualified to give specific advice appropriate to the NEC, so I will tell you what I did on my machine: I mounted a small ventilated...

13 replies | 823 view(s)

05-08-2022, 4:44 AM

Greg Quenneville replied to a thread Help with Hammer C3-31 from 2004 in General Woodworking and Power Tools

Good luck then in your search. I used to have a Felder CF731, now this BF6-31 from a couple of months earlier. I have reduced the pain of a combo...

13 replies | 757 view(s)

05-07-2022, 5:14 PM

Greg Quenneville replied to a thread Help with Hammer C3-31 from 2004 in General Woodworking and Power Tools

Hi Asger… 1. Don’t worry about the 20% faster speed…it was assumed that you were in the US with 60 Hz electricity. Since you are in 50 Hz land the...

13 replies | 757 view(s)

05-05-2022, 5:21 AM

Greg Quenneville replied to a thread Painters damaged original wood windows - ideas for a fix in General Woodworking and Power Tools

I would opt for new sash entirely. Routing out a rebate might work though if you can do it on a bench with good support. The profile looks like a...

27 replies | 2340 view(s)

04-28-2022, 7:48 PM

Greg Quenneville replied to a thread Shaper hold down clamps in General Woodworking and Power Tools

Airtight clamps seem to be the best, most expensive around. Popular with the Felder owners. You can find single action cylinders on the auction site...

26 replies | 1650 view(s)

Greg Quenneville
Contributor

Mini Statistics

Recent Visitors

Basic Information

About Greg Quenneville

Statistics

Total Posts

General Information

Greg Quenneville Contributor

Mini Statistics

Recent Visitors

Basic Information

About Greg Quenneville

Statistics

Total Posts

General Information

Greg Quenneville
Contributor