View Profile: Scott Shepherd - Sawmill Creek Woodworking Community

Yesterday, 8:04 AM

Keith Outten replied to a thread intarsia tree very detailed black walnut in Laser Engraving General Topics

I like your intarsia project Stan. I recently received two new moving skeleton plans in the mail and will start digitizing them soon.

4 replies | 518 view(s)

08-07-2022, 10:14 AM

Keith Outten replied to a thread State tax board lost my check in Off Topic Forum

Don't forget that your last option in any dealings with State government is your State Representative. They can blow though doors that are closed...

8 replies | 420 view(s)

08-06-2022, 12:56 PM

Keith Outten replied to a thread Dog Attack in Off Topic Forum

Riding a bike or when walking a belt buckle has been my best defense. If you wrap the belt around tour hand several times and leave just a few inches...

52 replies | 1806 view(s)

08-05-2022, 12:01 PM

Keith Outten replied to a thread A new guy in General Woodworking and Power Tools

Welcome to SawMill Creek Greg, the Massey looks fantastic.

13 replies | 792 view(s)

08-02-2022, 7:06 AM

Keith Outten replied to a thread Source Mailserver IP? (Not getting subscription emails) in Forum Tech Support

Scott, you need to become a Contributor again for mail to work.

6 replies | 941 view(s)

07-31-2022, 10:16 AM

Keith Outten replied to a thread Boxes from Uluru in Neanderthal Haven

Thanks for the beautiful pictures Derek. Looks like an amazing place to visit. I recently learned that Australia is a huge continent with a...

17 replies | 1545 view(s)

07-28-2022, 12:30 PM

Keith Outten replied to a thread New Dremel tool : Which one to get in Woodcarvers Forum

Michael, I lie the little Jet with the 90 degree head. I'll have to go looking for that one.

7 replies | 1242 view(s)

07-28-2022, 11:54 AM

Keith Outten replied to a thread Interesting new material - hempwood in General Woodworking and Power Tools

The State of Kentucky only recently changed their law to allow farmers to grow hemp. For law enforcement it is very difficult to distinguish hemp...

27 replies | 1442 view(s)

07-28-2022, 11:37 AM

Keith Outten replied to a thread Manuals in General Woodworking and Power Tools

Procedure for Longworth Chuck construction r3

13 replies | 3683 view(s)

07-28-2022, 11:33 AM

Keith Outten replied to a thread Manuals in General Woodworking and Power Tools

Jet 1221 Wood Lathe Manual

13 replies | 3683 view(s)

07-28-2022, 11:25 AM

Keith Outten replied to a thread Manuals in General Woodworking and Power Tools

Glazing - A step by step guide

13 replies | 3683 view(s)

07-28-2022, 11:14 AM

Keith Outten replied to a thread Manuals in General Woodworking and Power Tools

Rob, zip the file and upload using the Go Advanced option at the bottom right of this page. Then select Manage attachments and select the file from...

13 replies | 3683 view(s)

07-26-2022, 10:53 AM

Keith Outten replied to a thread New Dremel tool : Which one to get in Woodcarvers Forum

I own four Dremel tools, one of them I purchased in the late 70's and its been repaired several times. I also own a 80,000 rpm air grinder that...

7 replies | 1242 view(s)

07-26-2022, 10:35 AM

Keith Outten replied to a thread Been busy with intarsia in Woodworking Projects

Nice work Dennis, I am especially fond of the Cardinal.

6 replies | 779 view(s)

07-26-2022, 10:31 AM

Keith Outten replied to a thread Red Alder? in General Woodworking and Power Tools

Alder is a western USA species for the most part and for a long time it was considered only suitable for firewood. Today alder is pretty valuable for...

12 replies | 978 view(s)

07-19-2022, 11:48 AM

Keith Outten replied to a thread mobile base for Minimax FS41 Elite? in General Woodworking and Power Tools

Use a 4 by 4 bolted to the base under each end of the machine instead of a pallet. A mini pallet jack will slide under the base and is very easy to...

19 replies | 1219 view(s)

07-18-2022, 11:21 AM

Keith Outten replied to a thread My Version of the Hundred Ton Roller in Off Topic Forum

I have two of the IBC totes behind my barn. They catch rain water from the roof gutters and I bought a cheap well pump to provide the pressure...

1 replies | 445 view(s)

07-12-2022, 10:07 AM

Keith Outten replied to a thread Router table top in Shop Made Tools and Machines

I have router table extensions on both sides of my table saw that are machined commercially manufactured steel. Both have router raisers installed,...

10 replies | 2590 view(s)

Scott Shepherd
Moderator

Mini Statistics

More 10 Friends

Keith Winter

Bill Huber

Joe Pelonio

Belinda Barfield

Steve Schlumpf

John Kleiber

Join Groups 2 Groups

Trotec Laser Engravers Users Group

Univeral Laser Owners

Join Groups 1 Permission Groups

Recent Visitors

Basic Information

About Scott Shepherd

Signature

Contact

Statistics

Total Posts

General Information

10 Friends

Belinda Barfield

Bill Huber

David Dustin

Ed Lang

Joe Pelonio

John Kleiber

Keith Outten

Keith Winter

Scott M Smith

Steve Schlumpf

Scott Shepherd Moderator

Mini Statistics

More 10 Friends

Join Groups 2 Groups

Join Groups 1 Permission Groups

Recent Visitors

Basic Information

About Scott Shepherd

Signature

Contact

Statistics

Total Posts

General Information

10 Friends

Scott Shepherd
Moderator