View Profile: Jim Creech - Sawmill Creek Woodworking Community

Yesterday, 10:04 PM

Bruce Page replied to a thread Radio Garden, Radio stations around the globe in Off Topic Forum

That is way cool! Thanks for posting the link. It is fascinating to hear the different music forms from around the world. I wish there was a...

4 replies | 194 view(s)

02-26-2021, 11:06 PM

Bruce Page started a thread Space saving planner? in General Woodworking and Power Tools

Arrrg! I sold my PM15” planner & 8” jointer back in 2013 to make room for a new CNC router in my small, crowded 2-car garage shop. I no longer build...

3 replies | 340 view(s)

02-26-2021, 4:56 PM

Bruce Page replied to a thread Font type and size in Forum Tech Support

Verdana/10

10 replies | 500 view(s)

02-22-2021, 4:36 PM

Bruce Page replied to a thread Looking for a way to sand inside a cutting board handle with power tools in General Woodworking and Power Tools

I agree that curing the burning is the best solution. That said, I use the Scotch-Brite radial bristle discs and a Dremel tool to sand odd shapes....

18 replies | 642 view(s)

02-22-2021, 2:13 PM

Bruce Page replied to a thread Creeker's Past Week's Accomplishments in General Woodworking and Power Tools

My granddaughter asked me to make a stable sign for her horse, Danny.

14 replies | 415 view(s)

02-21-2021, 12:25 AM

Bruce Page replied to a thread Need to buy a CNC Shop Sabre is out!! in CNC Machines

My 24x36 Stinger 1

33 replies | 1458 view(s)

02-20-2021, 2:06 PM

Bruce Page replied to a thread Time for some levity in Off Topic Forum

A few more..

1137 replies | 99361 view(s)

02-19-2021, 3:52 PM

Bruce Page replied to a thread Good quality small drill chuck with ¼” hex drive? in General Woodworking and Power Tools

Donald, thanks. My objective was to find a physically "very small" chuck that I could use with my cnc router. The router has limited Z height –...

12 replies | 540 view(s)

02-19-2021, 12:43 AM

Bruce Page replied to a thread Time for some levity in Off Topic Forum

A few more..

1137 replies | 99361 view(s)

02-18-2021, 8:38 PM

Bruce Page replied to a thread 1 1/4'' id machined washer for laguna 1836 headstock in Turner's Forum

What is the OD & thickness? Have you contacted Laguna?

16 replies | 1102 view(s)

02-18-2021, 6:52 PM

Bruce Page replied to a thread Micro Adjustment of Table Saw Fence in increments as small as 0.001 inch in General Woodworking and Power Tools

Steven, that’s another nice TS addition. I made one a few years ago that slides on the fence tube with 5 neodymium magnets. I use it far more than I...

4 replies | 615 view(s)

02-18-2021, 6:29 PM

Bruce Page replied to a thread Good quality small drill chuck with ¼” hex drive? in General Woodworking and Power Tools

Keith, the third time is the charm. The Neiko 20753A chuck was delivered this morning and it runs true. I didn’t put an indicator on it but I cannot...

12 replies | 540 view(s)

02-16-2021, 5:39 PM

Bruce Page replied to a thread cnc machines for newbies in CNC Machines

That’s how mine’s set up. I prefer the direct control that allows me to adjust the rpm on the fly. I believe (could be wrong) that it is an...

36 replies | 2258 view(s)

02-16-2021, 4:56 PM

Bruce Page replied to a thread Good quality small drill chuck with ¼” hex drive? in General Woodworking and Power Tools

Steve, I want to use it in my cnc router for drilling odd size holes. Keith, I ordered a Neiko 20753A this morning that looks to have a different...

12 replies | 540 view(s)