View Profile: Dave Anderson NH - Sawmill Creek Woodworking Community

Yesterday, 1:32 PM

Bruce Page replied to a thread OneFinity Elite arrived - finally... in CNC Machines

Congrats! Looking forward to the "build".

4 replies | 142 view(s)

03-24-2023, 1:53 PM

Bruce Page replied to a thread Air Conditioner Coil and Condenser Cleaning in Off Topic Forum

Jim K, I would say that I’m probably more mechanically inclined than most. The issue with DIY is that the condenser is on the roof and at 72, I have...

11 replies | 478 view(s)

03-23-2023, 10:59 PM

Bruce Page replied to a thread Growth ring contest in General Woodworking and Power Tools

This “log” was given to me many years ago. It’s ~ 4” diameter x 6” long and heavy for its size. The black center is end to end. No idea what kind of...

34 replies | 2384 view(s)

03-23-2023, 10:32 PM

Bruce Page replied to a thread Time for some levity in Off Topic Forum

A few more for today.

2830 replies | 525403 view(s)

03-23-2023, 9:13 PM

Bruce Page started a thread Air Conditioner Coil and Condenser Cleaning in Off Topic Forum

How often should you have it done? Our AC (Bryant) has never been touched since it was installed 10 years ago. Am I living on borrowed time?

11 replies | 478 view(s)

03-23-2023, 10:42 AM

Dave Anderson NH replied to a thread Time for some levity in Off Topic Forum

Thursday's offerings.

2830 replies | 525403 view(s)

03-21-2023, 11:49 PM

Bruce Page replied to a thread recognize this band saw in Modesto in General Woodworking and Power Tools

I would make room for that in a heartbeat if it were local to me!

8 replies | 861 view(s)

03-20-2023, 2:37 PM

Dave Anderson NH replied to a thread Time for some levity in Off Topic Forum

silliness continues

2830 replies | 525403 view(s)

03-19-2023, 2:48 PM

Bruce Page replied to a thread Pocket knife vs TSA in Off Topic Forum

His Rusty Brick Road album is mellow and laid back. Yes, he was taken from us too soon. One day, we will beat cancer.

28 replies | 1627 view(s)

03-18-2023, 2:14 PM

Bruce Page replied to a thread Pocket knife vs TSA in Off Topic Forum

This is on my travel playlist.. https://davidmbailey.com/track/2192392/airport-song-aka-the-butt-song

28 replies | 1627 view(s)

03-18-2023, 1:43 PM

Dave Anderson NH replied to a thread Time for some levity in Off Topic Forum

Fodder for you.

2830 replies | 525403 view(s)

03-18-2023, 9:21 AM

Dave Anderson NH replied to a thread What is this in Off Topic Forum

looks like a double ended sailmakers needle to me.

14 replies | 863 view(s)

03-17-2023, 11:34 AM

Dave Anderson NH replied to a thread Pocket knife vs TSA in Off Topic Forum

Many years ago before 911 but after a rash of plane hijackings my wife and I went out climbing in the Tetons. On the way back at airline check in I...

28 replies | 1627 view(s)

03-16-2023, 4:58 PM

Dave Anderson NH replied to a thread Can the dead vote? Non-political in Off Topic Forum

My wife and I set up a revocable trust. The trust owns the house, all of our bank accounts including savings, and is an added insured on our cars. ...

100 replies | 5509 view(s)

03-16-2023, 4:47 PM

Dave Anderson NH replied to a thread Extinct Campbells soups in Off Topic Forum

Sorry Stephen, as a New Englander I can't cry over Manhattan Clam Chowder going extinct. Red tomato based "Clam Chowder" is in no way or shape clam...

27 replies | 1610 view(s)

03-16-2023, 1:23 PM

Bruce Page replied to a thread Vertical Fence in CNC Machines

Very cool John. I have often wished I had made provisions for a setup like that when I built the table for my Stinger. :(

8 replies | 642 view(s)

03-15-2023, 1:48 PM

Dave Anderson NH replied to a thread Time for some levity in Off Topic Forum

The silliness continues.

2830 replies | 525403 view(s)