View Profile: Eugene Dixon - Sawmill Creek Woodworking Community

Today, 8:46 AM

Eugene Dixon replied to a thread Creeker's Past Week's Accomplishments in General Woodworking and Power Tools

Finished dust collection closet by installing LED strip lighting on the two long walls mounted to flat boards at 45 degrees as "crown" molding. Spent...

5 replies | 69 view(s)

05-09-2022, 6:26 PM

Eugene Dixon replied to a thread Bandsaw Threw a Tire, Again in General Woodworking and Power Tools

Felder called Friday and left a message. They called again today. Not a lot of technical help and everything I might want has to come from Austria...

43 replies | 3690 view(s)

05-09-2022, 6:22 PM

Eugene Dixon replied to a thread Creeker's Past Week's Accomplishments in General Woodworking and Power Tools

Finished the DC closet and installed lights. Need to wire up the MS, etc. Waiting for the piping.

4 replies | 376 view(s)

05-03-2022, 8:21 AM

Eugene Dixon replied to a thread Bandsaw Threw a Tire, Again in General Woodworking and Power Tools

PM sent. Here are more characters to meet the limit.

43 replies | 3690 view(s)

05-03-2022, 8:16 AM

Eugene Dixon replied to a thread Creeker's Past Week's Accomplishments in General Woodworking and Power Tools

Ordered DC duct. Continued work on the closet. Worked on a few small pieces in prep for building a high vise.

7 replies | 586 view(s)

05-01-2022, 7:58 AM

Eugene Dixon replied to a thread Bandsaw Threw a Tire, Again in General Woodworking and Power Tools

Never saw a machinist detension a bandsaw blade during my career in equipment development in private industry, either. Just a habit I have gotten...

43 replies | 3690 view(s)

04-30-2022, 7:42 AM

Eugene Dixon replied to a thread Opinion of Hamlet Glenn Lucas tools in Turner's Forum

Ditto what Don said.

5 replies | 953 view(s)

04-30-2022, 7:38 AM

Eugene Dixon replied to a thread Bandsaw Threw a Tire, Again in General Woodworking and Power Tools

Faithfully de-tension after each use, Mike. the encouragement and the insight is appreciated.

43 replies | 3690 view(s)

04-25-2022, 9:19 PM

Eugene Dixon replied to a thread How to shorten glass tubes in Turner's Forum

I use 1" glass sample bottles for my light houses. I cut them to length with a 10" HF wet saw using a diamond blade then square the ends with 220...

10 replies | 1105 view(s)

04-25-2022, 9:14 PM

Eugene Dixon replied to a thread Sweeping compound in WorkShops

It takes a lot of sweeping compound to clean up joint compound dust.

23 replies | 2204 view(s)

04-25-2022, 9:12 PM

Eugene Dixon replied to a thread Creeker's Past Week's Accomplishments in General Woodworking and Power Tools

Focused on the DC closet all week. Finished the exterior this evening except for final mudding.

3 replies | 329 view(s)

04-25-2022, 9:06 PM

Eugene Dixon replied to a thread Bandsaw Threw a Tire, Again in General Woodworking and Power Tools

I'm behind in updating this thread. I installed the urethane tires using a jig (video) from the supplier. The jig made it easy. Basically to 1/2"...

43 replies | 3690 view(s)

04-25-2022, 10:05 AM

Eugene Dixon replied to a thread Bandsaw Threw a Tire, Again in General Woodworking and Power Tools

Where's the Hammer/Felder Service Department for the NE? I've called several times. Emailed multiple times. Even had the sales rep contact me for...

43 replies | 3690 view(s)

04-18-2022, 6:30 PM

Eugene Dixon replied to a thread Shop Build...should be a fun journey... in WorkShops

Planning on installing one of those on the house garage as soon as I can get the shaft above the door. Replacing a Wayne Dalton system which doesn't...

196 replies | 16772 view(s)

Eugene Dixon
Contributor

Mini Statistics

Recent Visitors

Basic Information

About Eugene Dixon

Statistics

Total Posts

General Information

Eugene Dixon Contributor

Mini Statistics

Recent Visitors

Basic Information

About Eugene Dixon

Statistics

Total Posts

General Information

Eugene Dixon
Contributor