View Profile: Eugene Dixon - Sawmill Creek Woodworking Community

Tab Content: All; Eugene Dixon; Friends; Photos

Older Activity
Yesterday, 4:28 PM

Eugene Dixon replied to a thread My Art in Turner's Forum

Cool factor on these is way up. Thanks for sharing

see more

2 replies | 180 view(s)
03-23-2023, 9:57 AM

Eugene Dixon replied to a thread Backache, so How high should lathe centers be? in Turner's Forum

My Robust AB is at elbow height. I keep telling myself I need to raise it. Maybe today.

see more

18 replies | 877 view(s)
03-21-2023, 5:26 PM

Eugene Dixon replied to a thread Another "Pucker" Bowl in Turner's Forum

Walls are 3/8" maybe. Bottom, almost too thin.

see more

3 replies | 427 view(s)
03-21-2023, 10:21 AM

Eugene Dixon started a thread Another "Pucker" Bowl in Turner's Forum

Turned this a couple of years ago. Pecan wood. ~8.5" diameter and ~7" tall. Here's the bowl base. Wondering about Osmo as a finish. ...

see more

3 replies | 427 view(s)
03-17-2023, 8:52 AM

Eugene Dixon replied to a thread Bosch Colt Bucked the Bit in General Woodworking and Power Tools

John, I've had it for more than 5 years, dunno exactly. Got it for a specific job when I was installing some flooring. It has been sporadically...

see more

5 replies | 636 view(s)
03-16-2023, 9:44 PM

Eugene Dixon started a thread Bosch Colt Bucked the Bit in General Woodworking and Power Tools

Grabbed the Bosch Colt to route some slots. Drilled the starter holes and wasted the slot on the drill press. Inserted the Whiteside bit into the...

see more

5 replies | 636 view(s)
03-14-2023, 10:34 AM

Eugene Dixon replied to a thread Creeker's Past Week's Accomplishments in General Woodworking and Power Tools

Spent time turning green, I think, Hackberry. Neighbor stopped by and made a much needed carb adjustment to the Husky 65, thankfully.

see more

17 replies | 1169 view(s)
03-12-2023, 7:32 PM

Eugene Dixon replied to a thread More Cherry Burl in Turner's Forum

Thank you, John.

see more

3 replies | 1015 view(s)
03-12-2023, 7:31 PM

Eugene Dixon replied to a thread Finishing Ebony in Turner's Forum

Thank you for the ideas.

see more

5 replies | 899 view(s)
03-12-2023, 7:50 AM

Eugene Dixon replied to a thread Bluebirds! in General Woodworking and Power Tools

Ted, Please, how did you mount the galvanized pipe? TIA

see more

31 replies | 2445 view(s)
03-11-2023, 8:57 AM

Eugene Dixon started a thread Finishing Ebony in Turner's Forum

Had a request for napkin rings from a dark wood. I scored a piece of ebony from an estate sale and turned these: Obviously, I didn't invest...

see more

5 replies | 899 view(s)
03-11-2023, 8:51 AM

Eugene Dixon started a thread More Cherry Burl in Turner's Forum

Thought the group might need a picture or two. I'm still finishing pieces from the 2019 donation of Cherry burl. C&C welcomed. The bowl is ~11"...

see more

3 replies | 1015 view(s)
03-05-2023, 8:29 AM

Eugene Dixon replied to a thread John Jordan woodturner, RIP in Turner's Forum

Robust is running a site wide sale right now.

see more

9 replies | 1918 view(s)
02-28-2023, 3:39 PM

Eugene Dixon replied to a thread Spiral Duct and Fittings Vendor - Raleigh, NC in WorkShops

+2 on Blastgate. Very helpful and responsive with my design, order, and outstanding CS on some issues that were probably my fault.

see more

7 replies | 1067 view(s)
02-24-2023, 10:07 PM

Eugene Dixon started a thread Thought about this too long in Turner's Forum

How to make a napkin ring, that is. Today I put a piece of ebony on the lathe, measured some napkin rings in the china cabinet and started turning. ...

see more

0 replies | 661 view(s)
02-24-2023, 8:27 AM

Eugene Dixon replied to a thread Recent bowls in Turner's Forum

Thanks Tim. I don't do the inlays often but I'll check into Easy Inlay.

see more

6 replies | 1039 view(s)
02-24-2023, 8:25 AM

Eugene Dixon replied to a thread New Shop construction question insulating the roof in WorkShops

Not sure where the OP is located within NC, but when I lived in ENC, heating days exceeded cooling days, albeit by a slim margin. Go figure. ...

see more

7 replies | 1210 view(s)
02-24-2023, 8:22 AM

Eugene Dixon replied to a thread Dual Tambour Door Track Layout in General Woodworking and Power Tools

Check out an old Hoosier cabinet. If I understand what the OP is asking, the Hoosier design has been around quite awhile. Looking across the room...

see more

9 replies | 664 view(s)

No More Results

Eugene Dixon
Contributor

Mini Statistics

Recent Visitors

Basic Information

About Eugene Dixon

Statistics

Total Posts

General Information

Eugene Dixon Contributor

Mini Statistics

Recent Visitors

Basic Information

About Eugene Dixon

Statistics

Total Posts

General Information

Eugene Dixon
Contributor