Dave Sabo
Contributor

they got those too! https://www.makitatools.com/products/tools/cordless/18v-lxt/dust-extraction Wouldn’t worry about the size of the...

If you have a sharp chisel - that’d be good enough. Doesn’t really matter if it’s honed with an Arkansas stone or latest micro diamond emulsion...

you could fill the holes / knots with epoxy to help with the tearout. How confident are you in the sharpness of your knives to begin with ?

In this quest for accuracy - do you really know whether your tool is accurate ? How? Did some org. like NIST certify it so ? If they did ,...

Given my experience , a “relatively large” island these days requires 5-6 receptacles.

It’s a quality bit and will handle it. Also, replacement bits are available for a reasonable cost if you do wear it out.

For my locations - if you can open a door , drw, ect…or remove it and touch the romex………..it has to be in conduit. If it’s in an inaccessible...

How about doing a test for us ? Take your best, sharpest chisels and run their edges along a piece of corian you have lying about. Make a few...

11 bucks for a plastic trash bag PLUS shipping ? Are you guys insane ?

Don’t know what you read or where - but it adjusts like any other press. I’d question the source, their competence and or their agenda. Does it have...

Wasn’t really very clear - my working theory is that the older crowd here was not taught to cut on or put hot pots directly on their countertops...

Makita sells the adapters - you need 22mm to …….. ? they call them “cuffs”. https://www.makitatools.com/products/details/417765-1 ...

You need to look for item # 203151 https://www.festoolusa.com/accessory/203151---ct-asasb-26whr-set#Overview

thanks Jim, I've always wondered about that. I also think the designs like Derek's would be even more prone to scratching the drills case and...

Melamine is fine as long as you don’t get the absolute cheapest , thinest stuff around. If you get a pantry from Calif. Closets Container...

Do the metal edges of the slots wear a groove on the drill's casing / overmolding from repeated removing and re-inserting ?

I'd be using this : https://www.industrialplywood.com/browse/cabinet-grade-products/cabinet-liner.html While there are paints that will hold...

osc005 is just backordered until the end of the month/early july. If I were doing window frames, I'd be looking at this with an assortment of...

Mahogany is easily available from sustainable sources today. You just need to be willing go pay for it.

Agreed. If your shop is already “dried in” , much of the advantage of these type products is wasted.

That depends . The 18v sanders from the big boys like dewalt, Makita, Milwaukee , ect…..with the battery on top get really heavy ( and unbalanced...

:eek: it must run constantly

Would an actual finger suffice ? https://www.youtube.com/watch?v=TFoo1ie9fYM hot dog if you insist :rolleyes:...

It’s not that new. Debuted pre-Covid at Ligna 2019 Was discussed here back then :...

I have some questions for the group - are you in the habit of putting hot pots and pans on your countertops ? Who taught you or advocated doing...

WD40 isn’t the greatest lubricant for protecting metal from wear and corrosion. Good for loosening rusty parts and displacing moisture , but at less...

Curious what you’re making and why the woodcraft offering isn’t satisfactory?

Time for a new wife :D Seriously though. How would one not cover up the countertop and still protect it ? Glass will dull your knives in short...

No , not really. I am somewhat dismissive of folks who love to say they "read on the internet" or " I saw on youtube" and somehow think the info...

Ah….. my favorite - a guy on youtooob said. I also read on the internet about a turnkey garage for $25k. You make it seem like lumber is the...