• Sections

  • Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Karl Card

    Help with low motor power on table saw

    Thread Starter: Karl Card

    Had a 7.5 baldor, had a seperate post on this because I thought I figured out what was going on but evidently this is beyond my knowledge or experience. I replaced caps on 7.5 baldor, no difference, bought new leeson 7.5 hp, both single phase motors, got it hooked up, check wiring, cranked...

    Last Post By: Tony Shea Yesterday, 5:28 PM Go to last post
    chris hood

    Router questions

    Thread Starter: chris hood

    My router on the recently purchased router table quit, it came on then off then on now it will not come on. I have it pulled apart trying to get all the sawdust out of the connections, it's embedded pretty bad, not sure if that is the cause but worth a try. I found another identical one on eBay for...

    Last Post By: Dan Rude Today, 4:19 AM Go to last post
    Jerry Bruette

    Surveys

    Thread Starter: Jerry Bruette

    How is the Margin Of Error determined for a survey? I don't care who does the survey or what it's for I'm just curious how the margin is determined and who determines it.

    Last Post By: Jim Koepke Today, 2:00 AM Go to last post
    Warren Lake

    hard not to love the blues

    Thread Starter: Warren Lake

    Been watching Matteo for years and now many top players are recognizing him. I think hes 24 now. Video is not great and sound not great but I can hear whats going on. Very nice of Joe to bring him up and others that are spending time with him. Hes innovative. Very unique finger picking style....

    Last Post By: Maurice Mcmurry Yesterday, 8:44 PM Go to last post
    Nick Crivello

    Economics of milling vs store bought hardwoods?

    Thread Starter: Nick Crivello

    I'm pondering the economics of a mill vs buying rough lumber at retail/wholesale. In the Bay Area, depending on where you shop hardwoods like Oak and walnut can run up to $15-18bf/ft, or more for the rift/quarter sawn stuff. If one is able to source your own logs, running your own mil and kiln...

    Last Post By: Maurice Mcmurry Yesterday, 7:06 PM Go to last post
    Rob Luter

    Tally Ho

    Thread Starter: Rob Luter

    Apologies if this has been posted previously, but my search of the forum found nothing. I've been watching this series for a number of weeks now and found it fascinating. It covers the restoration/rebuilding of a 100 year old sailing yacht. The scale of the build is huge and I can't imagine the...

    Last Post By: Alan Rutherford Yesterday, 10:59 PM Go to last post

  • Recent Polls

    What are your thoughts? (Votes: 6)

    1. Been doing it like (or equivalent) this for years. (Votes: 4)

    2. Wow! Never thought of that. (Votes: 0)

    3. Been doing it with mirrors. (Votes: 2)

    4. Ain't got a boat, truck, care… (Votes: 0)

  • Recent Forum Posts

    Maurice Mcmurry

    Bandsaw blades

    WoodMizer Double Hard blades are similar to Bi-Metal. Tooth count and length are limited. Lennox were preferred in the shop with the big ship saw but

    Maurice Mcmurry Today, 6:32 AM Go to last post
    Josko Catipovic

    PM 1500 or Laguna 18BX Bandsaw?

    I have a Laguna LT18 with a 1 1/4" resaw master. It can take off a clean 1/16" off a 12" oak plank but I'm limited by my ability to feed

    Josko Catipovic Today, 6:14 AM Go to last post
    STUART Robertson

    Bandsaw blades

    Looking for small profiles 1/4 " or 6mm

    STUART Robertson Today, 6:01 AM Go to last post
    richard shelby

    What finishes over oil

    shellac will work also. I routinely spray shellac over BLO ​with no problems.

    richard shelby Today, 5:44 AM Go to last post
    Tom Trees

    Bandsaw blades

    I reckon you could possibly get carbide for the same cost as the m42 blades.
    Tai-Fu has a post or two, though you might have to visit the official

    Tom Trees Today, 4:33 AM Go to last post

  • Recent Blog Posts