Sawmill Creek Woodworking Community - The Sawmill Creek Press

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Time for some levity
Thread Starter: Dave Anderson NH
With all of the negativity and political stuff going on with the Covid-19 virus it is time to look at the humorous side of things. Feel free to add more, but keep it clean or it will be deleted.
Last Post By: Jim Allen Today, 1:05 PM

Dining room carver chairs - Take 2
Thread Starter: Derek Cohen
About a month ago I began a thread about designing and building two carver chairs to accompany the 6 bentwood chairs we have owned for the past 40 years. The chairs were purchased all those years ago along with a table, which is around 200 years old. We need a larger table, and time has come to...
Last Post By: Derek Cohen Today, 12:54 PM

Help with low motor power on table saw
Thread Starter: Karl Card
Had a 7.5 baldor, had a seperate post on this because I thought I figured out what was going on but evidently this is beyond my knowledge or experience. I replaced caps on 7.5 baldor, no difference, bought new leeson 7.5 hp, both single phase motors, got it hooked up, check wiring, cranked...
Last Post By: Holmes Anderson Today, 7:42 AM

Any ideas on Kubota D902 engine that won't start at low throttle?
Thread Starter: Brian Elfert
I have a 2019 Grasshopper mower with Kubota D902 engine that suddenly won't start at low throttle. I have always started it at the lowest throttle setting and it started just fine. Now, it simply won't start at the lowest throttle setting. I thought something was seriously wrong, and I was just...
Last Post By: Jim Becker Today, 12:26 PM

I need some cabinetry tool advice.
Thread Starter: Justin Mullins
I'm looking to build my first set of cabinets in my kitchen. I'm currently building a new house. I am a third generation general contractor so l have a good degree of knowledge in construction my grandfather used to build furniture and cabinets so I have a very good general idea of how they need to...
Last Post By: Ron Selzer Today, 12:49 PM

What hand tool skill do you want to Learn?
Thread Starter: Mike Allen1010
One of the things I enjoy about wood working is the potential to learn new skills that enhance my over all enjoyment of the craft. As a Neander, often these new skills don't require an extensive investment in new tools. I've been a hand tool wood worker for >40 years and early on everything...
Last Post By: Mike Allen1010 Today, 11:29 AM

The Sawmill Creek Press
Woodshop for Kids.....is not just woodworking

by
Jack McKee

View Profile

View Forum Posts

View Blog Entries

View Articles

Published on 01-31-2015 9:16 PM

Woodworkingfor Kids.....isnot just woodworking

Kids need Hands On activities. ...

Read More 4 Comments
Using CA Glue in Woodturning

by
Wally Dickerman

View Profile

View Forum Posts

View Blog Entries

View Articles

Published on 11-23-2014 6:59 AM

There have been some recent threads on CA glue on the Turners forum. The following is an article I did for my turning club ...

Read More 6 Comments

Recent Polls
What are your thoughts? (Votes: 6)

Been doing it like (or equivalent) this for years. (Votes: 4)

Wow! Never thought of that. (Votes: 0)

Been doing it with mirrors. (Votes: 2)

Ain't got a boat, truck, care… (Votes: 0)
Recent Forum Posts

Emma Cook the Tiny Turner

These threads for whatever reason often go off topic, why not just enjoy the video for the reason the O.P. intended without negative commentary?
allen thunem Today, 1:50 PM

LV Canvas chisel Gouge roll?

The larger size is 10 1/2-11" wide- the size of timber chisels.

Good luck!
Cameron Wood Today, 1:32 PM

Small Cherry Bowl

Patrick, that's quite a compliment - thank you kindly. Some explanation on thickness. The very bottom of the bowl (so the area inside the foot) is 3/16ths
John Kananis Today, 1:23 PM

LV Canvas chisel Gouge roll?

I looked at those, but they look to be designed for Japanese chisels and would be too short. Most of my chisels are 10-12 inches long. I have ordered
Patrick C Daugherty Today, 1:14 PM

Ulmia double rabbet plane

Here are some screen grabs of a Ulmia double rabbet plane that is for sale. I haven't seen this one before, but I find the unadorned basics of the design
Mark Gibney Today, 1:05 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

The Sawmill Creek Press

Recent Polls

Recent Forum Posts

Recent Blog Posts