Sawmill Creek Woodworking Community - The Sawmill Creek Press

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Time for some levity
Thread Starter: Dave Anderson NH
With all of the negativity and political stuff going on with the Covid-19 virus it is time to look at the humorous side of things. Feel free to add more, but keep it clean or it will be deleted.
Last Post By: John Ziebron Yesterday, 10:59 PM

Dining room carver chairs - Take 2
Thread Starter: Derek Cohen
About a month ago I began a thread about designing and building two carver chairs to accompany the 6 bentwood chairs we have owned for the past 40 years. The chairs were purchased all those years ago along with a table, which is around 200 years old. We need a larger table, and time has come to...
Last Post By: Larry Frank Yesterday, 8:42 PM

Help with low motor power on table saw
Thread Starter: Karl Card
Had a 7.5 baldor, had a seperate post on this because I thought I figured out what was going on but evidently this is beyond my knowledge or experience. I replaced caps on 7.5 baldor, no difference, bought new leeson 7.5 hp, both single phase motors, got it hooked up, check wiring, cranked...
Last Post By: Jimmy Harris Today, 11:46 AM

Additional Sealant for Pressure Treated Lumber?
Thread Starter: Thomas McCurnin
I've got a well head cabinet/enclosure to make which is in a remote location, about a 2 mile hike through the mountains without any trails. I've spent a few hours making measurements, and we will likely make this in sections, and strap them to our backs and assemble it in the field. There is no...
Last Post By: Maurice Mcmurry Today, 7:46 AM

Router questions
Thread Starter: chris hood
My router on the recently purchased router table quit, it came on then off then on now it will not come on. I have it pulled apart trying to get all the sawdust out of the connections, it's embedded pretty bad, not sure if that is the cause but worth a try. I found another identical one on eBay for...
Last Post By: chris hood Yesterday, 10:16 PM

Any ideas on Kubota D902 engine that won't start at low throttle?
Thread Starter: Brian Elfert
I have a 2019 Grasshopper mower with Kubota D902 engine that suddenly won't start at low throttle. I have always started it at the lowest throttle setting and it started just fine. Now, it simply won't start at the lowest throttle setting. I thought something was seriously wrong, and I was just...
Last Post By: Jerome Stanek Today, 11:27 AM

The Sawmill Creek Press
Woodshop for Kids.....is not just woodworking

by
Jack McKee

View Profile

View Forum Posts

View Blog Entries

View Articles

Published on 01-31-2015 9:16 PM

Woodworkingfor Kids.....isnot just woodworking

Kids need Hands On activities. ...

Read More 4 Comments
Using CA Glue in Woodturning

by
Wally Dickerman

View Profile

View Forum Posts

View Blog Entries

View Articles

Published on 11-23-2014 6:59 AM

There have been some recent threads on CA glue on the Turners forum. The following is an article I did for my turning club ...

Read More 6 Comments

Recent Polls
What are your thoughts? (Votes: 6)

Been doing it like (or equivalent) this for years. (Votes: 4)

Wow! Never thought of that. (Votes: 0)

Been doing it with mirrors. (Votes: 2)

Ain't got a boat, truck, care… (Votes: 0)
Recent Forum Posts

Abranet Sanding Sheets- Leaving Scrapes & Streaks

Yes, I see it all the time when I sand metal surfaces, it's more obvious there but the same thing happens on raw wood or finishes.

Whatever
Rafael Herrera Today, 12:32 PM

Paralysis by analysis.....

A similar thing is where you do something amazing because you don't know ahead of time how hard it's supposed to be.

I worked on a large
Lee DeRaud Today, 12:30 PM

Router help needed.

Not a problem as long as you set the depth of cut appropriately.

Make sure you've first sized the plywood to slightly larger than the Jessem
Mike King Today, 12:19 PM

Router help needed.

I have a router plate - actually a Jessem Router Lift II - that I need to use as a template.
This is sort of in reverse of what's normally done.
Rich Engelhardt Today, 12:11 PM

Help with low motor power on table saw

Those are always the most difficult repairs. When your replacement part works the same as your old part, it's almost always safe to assume that the problem
Jimmy Harris Today, 11:46 AM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

The Sawmill Creek Press

Recent Polls

Recent Forum Posts

Recent Blog Posts