Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Shop Build...should be a fun journey...
Thread Starter: Jim Becker
I debated about starting this thread now or later, but decided on now because, well...I might forget something. :o As a little background, at our previous property, I was blessed with a reasonably sized, fully conditioned space for my shop in what was originally a three-and-a-half vehicle garage...
Last Post By: glenn bradley Yesterday, 9:45 AM

Dust Collector recommendations
Thread Starter: Michael Rutman
Oh boy, reading the archives I can see this is not a simple question, which makes me feel good because I am completely lost. I have never owned a dust collector mostly due to inability to figure out what I need, and that needs to change. So, let me go over my shop, my needs, and then beg for...
Last Post By: Eric Arnsdorff Yesterday, 11:34 PM

VFD for 7.5 hp 3 phase to run on 220 single phase
Thread Starter: Mike Leiferman
Anyone with any experience running a 7.5 hp 220 volt 26 amp 3 phase from a VFD powered by 220 single phase? I would like to know a) what specific vfd you are using if you recommend it, b) any issues I should be aware of The motor is driving a 1995 Lazzari Tema 3000i. The alternative for me...
Last Post By: Jared Sankovich Yesterday, 10:04 AM

Cost effectiveness of a slider vs. tracksaw & tablesaw
Thread Starter: Jonathan Jung
I thought about posting this to the business section, because I'd really like input from professionals who use their shop as a business. For those of you who make $ or even a living making furniture or cabinets, how long does it take for a sliding table saw to pay for itself compared to a track saw...
Last Post By: Kevin Jenness Yesterday, 9:49 AM

Anyone have experience with Sheds Unlimited?
Thread Starter: Roger Feeley
We are looking into building a 3 car garage with living space above. https://shedsunlimited.net/garages/legacy-workshop-three-car-garage/ These folks will manufacture modules and erect the shell. Then it’s up to us to finish it.
Last Post By: Brian Elfert Yesterday, 9:44 PM

Hollow grind with cbn wheel on low speed grinder- how far do you go?
Thread Starter: Assaf Oppenheimer
Hi all, I'm getting a slow speed grinder with a cbn wheel. I've never done hollow grinds myself. Would appreciate it if any experienced woodworker could advise how much to grind on the blade before you risk edge temper. Pics would be welcome. Thanks!
Last Post By: Leigh Betsch Yesterday, 9:45 AM

Rich Engelhardt

There is no available content written by Rich Engelhardt

Recent Polls
Recent Forum Posts

Repair of scratch in varnish

Thanks john
Charles Grauer Today, 6:23 AM

cub cadet older LTX-1142 Hydrastatic, start issue

Kohler motor and its great. Sidetracked getting the hospital bed together. Done now just deliver and set up

the mower does have a separate
Warren Lake Today, 2:09 AM

Water heater anode school please

Good point Bruce.

jtk
Jim Koepke Today, 1:45 AM

12" Craftsman Band Saw, 1938ish

I have two versions of the Craftsman 12" band saw model 102.01121, and I will keep and restore one of them.
They are slightly different from
Mark Gibney Today, 12:44 AM

Dust Collector recommendations

Luis I looked at the Supercell until I saw the CFM rating of 465 CFM. Then I realized what it is.

It is an interesting and unique product.
Eric Arnsdorff Yesterday, 11:34 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Rich Engelhardt

Recent Polls

Recent Forum Posts

Recent Blog Posts