• Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Derek Cohen

    Exasperated with Fine Woodworking Magazine!

    Thread Starter: Derek Cohen

    About 10 days ago I received an email to say that my on-line subscription with FWW magazine could not be renewed as the credit card details were incorrect. I checked, and they were up to date. I have been a longstanding on-line member and paying a low fee ($19.95) because of this. To renew, I...

    Last Post By: J. Greg Jones Today, 6:20 AM Go to last post
    Mark Gibney

    Shoulder injury

    Thread Starter: Mark Gibney

    I'm looking for feedback from any of you who have or had shoulder issues. For a year I've had a bad left shoulder. Grew worse over the summer. Would wake me up a lot at night. Got to the point it was difficult to put on a shirt or jacket. And certain movements would cause a lot of pain for 30...

    Last Post By: Jerome Stanek Today, 11:28 AM Go to last post
    steven c newman

    A new Desk for me

    Thread Starter: steven c newman

    "old" one is cramped, small drawers....not enough room for the computer I am using...so. Came up with a rough "Plan".. Picked up about 40bf of Ash....($20.....) Then drew up a better Plan... More as a guide, than anything carved in stone....(already a few design changes have been made..)...

    Last Post By: Tony Zaffuto Today, 5:49 AM Go to last post
    Joe Beaulieu

    Sharpening Forum?

    Thread Starter: Joe Beaulieu

    Hi All, i am really surprised there is not a separate section of this forum for sharpening. I have as many sharpening questions as I do woodworking questions. I am sure I am not the first to raise this idea. Just a thought. Thanks Joe

    Last Post By: Jim Koepke Today, 1:47 PM Go to last post
    Dennis Yamamoto

    looking for recommendation - trim router for routing small mortises

    Thread Starter: Dennis Yamamoto

    I need to route mortises for some small brass knife hinges. For routing these small mortises, what trim router would you buy today, and why? For me it seems like good depth adjustment, and having control and visibility for small details would be most important. Here's a couple that I have...

    Last Post By: Prashun Patel Today, 8:58 AM Go to last post
    lowell holmes

    Tool rust prevention

    Thread Starter: lowell holmes

    In the current issue of This Old House Magazine, a reader ask Tom Silva how he prevents rust on his tools. I live in Galveston County Texas, so I Know a bit about rust. I coat my tools with Johnson's Floor Wax. They do not rust. I thought some new woodworkers might be interested.

    Last Post By: lowell holmes Today, 9:43 AM Go to last post
  • James Pallas

    There is no available content written by James Pallas
  • Recent Polls

  • Recent Forum Posts

    Kev Williams

    Cw-5000 chiller s&a, cw-5000 d&a

    I have an S&A 5200, and it works. What else to say?

    As to faked tubes, my guess is 'those' sellers are stating tested wattages rather

    Kev Williams Today, 2:20 PM Go to last post
    Braden Todd

    Radian Laser Systems

    Sounds good!

    The disc rotary is pretty great! I think a co2 and the disk rotary would work very well for the powder coat, pending the laser

    Braden Todd Today, 2:19 PM Go to last post
    Steven Harrison

    Which Bench Grinder?

    I just bought a Rikon 8 inch slow speed grinder from Rockler that was on sale for $100. I added the Veritas grinder tool rest and jig and am pretty happy

    Steven Harrison Today, 2:09 PM Go to last post
    freiler thompson

    Keepsake Box

    Hi Mike,

    Yes it was done as a closed box then cut off. Good catch, I did not realize that the top had been rotated.

    I tried

    freiler thompson Today, 2:00 PM Go to last post
    Jim Koepke

    Sharpening Forum?

    It really depends on how dull it is. Yesterday a chisel being prepared for my grandson only needed a bit of touch up on a polishing stone. Another chisel

    Jim Koepke Today, 1:47 PM Go to last post
  • Recent Blog Posts