Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Time for some levity
Thread Starter: Dave Anderson NH
With all of the negativity and political stuff going on with the Covid-19 virus it is time to look at the humorous side of things. Feel free to add more, but keep it clean or it will be deleted.
Last Post By: Dave Zellers Today, 9:10 PM

How to replace Syder/Coupler on Supermax 16/32>?
Thread Starter: Thomas Colson
I have a Supermax 16/32 with a pretty clapped out rubber spyder-coupler. Little tiny pieces of rubber are coming out of it, which makes sense, I've used this like I stole it for the last 2 years. Any videos or instructions with pictures anywhere on how to do this that are deliberately hidden and...
Last Post By: Jerry Bruette Today, 4:13 PM

Help Me Pick a Plow Plane or Is It a Plough Plane
Thread Starter: Thomas McCurnin
Typical use will be on 3/4 to 7/8" stock planing on edge for a a 1/4" groove about 3/8" deep for frame and panel construction. I'll also be using it for grooving a post, usually about 1.5" x 1.5" is typical, again to accept a panel for frame and panel construction. It needs to go both directions,...
Last Post By: Derek Cohen Today, 7:45 PM

I hate rusty saws, but...
Thread Starter: Richard Hutchings
I just saw an ad for 7 rusty saws for $25 and I may not be able to resist. One has the thumbhole but broken horn. It might be worth buying the whole lot but I'll have to get better at cleaning them up. I hate the mess. Hopefully someone will buy them before I decide to bite the bullet.
Last Post By: Maurice Mcmurry Today, 9:51 AM

VFD for 7.5 hp 3 phase to run on 220 single phase
Thread Starter: Mike Leiferman
Anyone with any experience running a 7.5 hp 220 volt 26 amp 3 phase from a VFD powered by 220 single phase? I would like to know a) what specific vfd you are using if you recommend it, b) any issues I should be aware of The motor is driving a 1995 Lazzari Tema 3000i. The alternative for me...
Last Post By: Matt Day Today, 8:58 PM

Painters damaged original wood windows - ideas for a fix
Thread Starter: Tim Vanderet
Hi All, I've spent a lot of time reading and learning in these forums, so thank you to everyone who makes this a valuable resource. We are having some work done on our home in the SF Bay Area of California and our painters got overzealous with scraping the old paint off of the windows and...
Last Post By: Tom Bender Today, 7:35 AM

Ed Aumiller

There is no available content written by Ed Aumiller

Recent Polls
Recent Forum Posts

Kitchen Cabinet Refinishing - DIYer can't decide on materials

Impervo apparently has limited availability. Our story still has lots. It is the best paint I have ever applied for interior trim, doors, cabinetry etc.
Maurice Mcmurry Today, 10:04 PM

ID & advice - Robland slider

John,

I will not put your details on the internet. That is to protect you. No magic involved, just common sense.

If
Rick Potter Today, 10:00 PM

Anyone have experience with Sheds Unlimited?

It's not Sheds Unlimited but a client just bought a shed from a local "Amish" source. It has lots of particle board. Siding, Flooring, and Sheeting
Maurice Mcmurry Today, 9:51 PM

18 foot 4/4 cherry for kayak

Doubt that would be an option for kayak building. He'd want kiln dried, clear, straight-grain material.

This is why cedar and spruce are
andy bessette Today, 9:48 PM

Polyaspartic Garage Floor Coating?

I have done a several DIY epoxy garage floor coatings from various stores for several Clients. They are OK and I was able to cut the cost way down compared
Maurice Mcmurry Today, 9:40 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Ed Aumiller

Recent Polls

Recent Forum Posts

Recent Blog Posts