Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

How to bend wood like this - Outdoor furniture project
Thread Starter: Alan Lightstone
Looking for a new project to do. I've been spending a few months upgrading the workshop / fixing minor annoyances, and really need to actually build something. I ran across this in a magazine ad. The furniture is supposedly solid teak, though I don't think that will be in the cards for...
Last Post By: Mike King Today, 3:50 PM

Are they building standalone car washes like crazy in your area too?
Thread Starter: Brian Elfert
They are going crazy building standalone car washes in my area. I know of at least three currently under construction nearby, and a few others that recently opened. Car washes are going up all over the Minneapolis metro area. There will easily be three times as many standalone car washes once...
Last Post By: Brian Elfert Yesterday, 4:24 PM

landscaping is my other hobby, record for me, 25 yards of mulch
Thread Starter: Brian Runau
My landscape guys clean up the beds and install mulch for me now, too old, but I planted everything you see except the very large mature trees. Shade garden, cutting garden, front. Thanks Brian
Last Post By: Brian Runau Today, 1:07 PM

SCM T130 bearing change
Thread Starter: Tom Yaegle
Has any one here done one? Looking for suggestions, thanks.
Last Post By: Jerry Bruette Today, 1:23 PM

LLAMBRICH Intergrated arbor and chuck
Thread Starter: Patty Hann
Opinions, please on integrated arbor and chuck for a DP. Am looking at the LLAMBRICH Keyless chucks ... integrated 2MT shank/arbor 1/32" to 3/8" (part# JK10-MT2) 1/32" to 1/2" (JK13-MT2) Thanks
Last Post By: Patty Hann Today, 1:45 PM

Lumber supply
Thread Starter: steven c newman
Has been restocked.. Bought 10 planks...for $30...had to cut a few of the 10 footers down, to fit into the Trunk of my Chevy Equinox... Eight 1 x 6 x 6' Five 1 x 4 x 6' And he threw in a stack of shorts And a 3/4" x 8" x 39" slab..
Last Post By: steven c newman Today, 11:03 AM

Tim Howell

There is no available content written by Tim Howell

Recent Polls
Would you borrow a tool from someone? (Votes: 71)

Sure - why not? (Votes: 9)

Never. If I needed something, I'd buy or rent it. (Votes: 10)

Maybe. Depends on the person and the tool. (Votes: 52)
Recent Forum Posts

How to bend wood like this - Outdoor furniture project

Kiln dried lumber is not an issue with bent lamination. You need 1) laminates that are thin enough to be able to bend around your form, 2) an appropriate
Mike King Today, 3:50 PM

Outdoor Oak Table

I assumed the OP knew this or said table is under complete coverage and only subject to temperature swings. I agree though, it isn't something I'd normally
Michael Burnside Today, 3:44 PM

How to bend wood like this - Outdoor furniture project

Pneumatic pressure is effectively more clamps. And potentially dangerous, as said well above.
Mike King Today, 3:26 PM

Stopped by Liberty Tool Co

I’ve had good luck with Peter Galbert’s drawsharp. Benchcrafted sells them, though they are currently out of stock

https://benchcrafted.com/products/dr...42645357625520
Steve Boring Today, 3:26 PM

Gable Vent

I posted on this yesterday, but it is not here.

Best airflow and louver vents are mutually exclusive.

Not too hard to make as
Cameron Wood Today, 3:05 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Tim Howell

Recent Polls

Recent Forum Posts

Recent Blog Posts