Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Bad job coming
Thread Starter: Tom M King
I have these two raised panel garage doors to refinish on a lake rental house. Just testing a couple of panels, it won't be too bad sanding down to bare wood, but someone had put another coat of marine varnish on the bottom two sections, so those are going to get some work with a heat gun before...
Last Post By: Tom M King Today, 5:28 PM

Harvey Slider on Unisaw?
Thread Starter: John Kananis
All these slider threads got me thinking. Does anyone here have the Harvey compass st-1500 attached to their unisaw? Can you speak on the quality, ease of attachment, capabilities and shortcomings? Thank you in advance!
Last Post By: John Kananis Today, 10:40 AM

SCM T130 bearing change
Thread Starter: Tom Yaegle
Has any one here done one? Looking for suggestions, thanks.
Last Post By: Tom Yaegle Today, 6:11 PM

Spindle gouge bevel angle?
Thread Starter: John Kananis
I have a 1/2" sorby detail gouge that I have ground at 40° (also removed the heel) and it works ok now that I moved away from the jigs and started sharpening by hand... but it's still just an ok tool. I now have a d-way detail spindle gouge (1/2") on the way and was thinking about trying a 25°...
Last Post By: Don Frank Today, 8:57 AM

Powermatic Model 80 20" Bandsaw - Yes or No?
Thread Starter: Brent Ring
All, I have been in the market for a bigger bandsaw. Starting to build some rocking chairs a la Hal Taylor, and my PM 141 does not have enough clearance to make a few of the cuts needed. A Powermatic 80 20" had come up in my area, for a little under $1k. Owner states it runs smooth, cuts well....
Last Post By: Mickey Plunkett Today, 11:47 AM

Dumb answers to dumb questions
Thread Starter: Zachary Hoyt
I used to feel frustrated when I would have listed something for sale on Craigslist or Facebook and included the town where I lived, and instead of looking it up on their devices people would write to me to ask "where is Orwell" (where I used to live) or now "where is Piercefield?". I finally...
Last Post By: Larry Edgerton Today, 5:50 PM

Adam Bauer

There is no available content written by Adam Bauer

Recent Polls
Would you borrow a tool from someone? (Votes: 71)

Sure - why not? (Votes: 9)

Never. If I needed something, I'd buy or rent it. (Votes: 10)

Maybe. Depends on the person and the tool. (Votes: 52)
Recent Forum Posts

Source for Cuban Mahogany (Swietenia mahagoni)

here's a place that might have what you are looking for. Google Maps says it is just under 4 hours to Albany. I have not use them, but several of my family
Ernie Hobbs Today, 6:32 PM

Total Boat Epoxy?

Carrol,
Can you put up a photo of the two sashes to be glued side by side? This is new to me.
If it's stile to stile with a spline in between,
William Hodge Today, 6:30 PM

Sandblasting

For fine work you cut stencils from blasting frisket.
Richard Coers Today, 6:12 PM

Freud hand held router FT2200VCE bit is moving

Upcut spirals require a little more umph when installing because the knives are pulling the bit down into the cut. Also may want to check the bearings
Larry Edgerton Today, 6:12 PM

SCM T130 bearing change

Jerry, It is a nyloc nut.

For the rest of you SCM shaper owners you may want to check for a grease cup. Fill cup with grease and tighten
Tom Yaegle Today, 6:11 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Adam Bauer

Recent Polls

Recent Forum Posts

Recent Blog Posts