Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

How to bend wood like this - Outdoor furniture project
Thread Starter: Alan Lightstone
Looking for a new project to do. I've been spending a few months upgrading the workshop / fixing minor annoyances, and really need to actually build something. I ran across this in a magazine ad. The furniture is supposedly solid teak, though I don't think that will be in the cards for...
Last Post By: Alan Lightstone Yesterday, 9:49 AM

Lumber supply
Thread Starter: steven c newman
Has been restocked.. Bought 10 planks...for $30...had to cut a few of the 10 footers down, to fit into the Trunk of my Chevy Equinox... Eight 1 x 6 x 6' Five 1 x 4 x 6' And he threw in a stack of shorts And a 3/4" x 8" x 39" slab..
Last Post By: steven c newman Yesterday, 11:20 PM

Residential fence rules
Thread Starter: Stan Calow
I am looking for what people in other jurisdictions have dealt with. I have always understood that, in my city, fences between homes were the responsibility of the homeowner who first puts it up. And the rule was "good side out" and 6" off the property line. But after a discussion with a...
Last Post By: Terry Therneau Yesterday, 11:02 PM

Seeking Recommendation on a Bench Grinder with Specific Features.
Thread Starter: Scott Memmer
Hi, Everyone. I dearly love this forum, although I have not posted in a long time. You folks are so knowledgeable and always have such great suggestions. Here is my situation. I make a small music accessory and need to build my own saw. Without going into all the details, I've been searching for...
Last Post By: Ray Selinger Yesterday, 5:12 PM

Harvey COMPASS RG-1/RG-2 Universal Roller Guides Question
Thread Starter: James Cheever
All - Has anyone seen or used the Harvey COMPASS RG-1/RG-2 Universal roller guides. They look solid and would be a pretty useful addition to my shop, but the price seems way too high. I'd love to hear any feedback. Thanks.
Last Post By: Lloyd McKinlay Yesterday, 9:46 PM

Anyone with temperature controller experience?
Thread Starter: Doug Garson
I'm volunteering for a food bank and trying to set up a cold room to store produce and other perishables. The main cooling will be done by a pair of air conditioners controlled by a Coolbot which enables the air conditioners to cool the room down below the usual lower limit for air conditioners...
Last Post By: Bill Dufour Yesterday, 4:20 PM

Adam Blanton

There is no available content written by Adam Blanton

Recent Polls
Would you borrow a tool from someone? (Votes: 71)

Sure - why not? (Votes: 9)

Never. If I needed something, I'd buy or rent it. (Votes: 10)

Maybe. Depends on the person and the tool. (Votes: 52)
Recent Forum Posts

titebond clamping force for wasteblocks

Thanks for all the replies folks, which were very helpful. I searched a bit more and found some earlier threads on SMC and elsewhere on this topic more
Dan Gaylin Today, 9:35 AM

California bans gas lawn mowers and leaf blowers after 2024

Ditto. I live in the Pigeon River State Forest, and it is necessary to keep a yard mowed for ticks. Check out Permethrin. I buy a quart of concentrate
Larry Edgerton Today, 9:31 AM

PM3520B fwd/rev switch issue

Ricc, you are correct, my bad the center off switch is from another project I was working on. The diagram I posted earlier is correct for the PM forward-reverse
Sam Force Today, 9:23 AM

California bans gas lawn mowers and leaf blowers after 2024

No batteries for me. My lawn is about four and a half acres so I use a 35HP gas (really fast) mower. I have nineteen large mature trees in my yard plus
Keith Outten Today, 9:14 AM

Bandsaw Dust Collection Improvement

Hi John - apologies for the off topic reply, but whilst I too am looking for better dust collection for my Laguna 14/12, I saw you post in another forum
Louis Joyce Today, 9:06 AM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Adam Blanton

Recent Polls

Recent Forum Posts

Recent Blog Posts