• Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Bennie Dempsey

    3D Planning Software

    Thread Starter: Bennie Dempsey

    Hey all! I would like to start planning out my projects before I begin them, as I've heard that's a good habit to have. I can find a modeling program online pretty easily, but I wanted to see what you guys use. I am awful at hand drafting so paper and pencil isn't my go-to for personal projects....

    Last Post By: Mark Bolton Yesterday, 5:06 PM Go to last post
    Tim M Tuttle

    Jointer Safety

    Thread Starter: Tim M Tuttle

    I've been milling up a lot of white oak the past two nights. While I was using my jointer I started to ponder safety. For something like the table saw there are a lot of common safety procedures/dos/donts. A lot more than a jointer which makes sense as there are a lot more variables with the...

    Last Post By: Andrew More Yesterday, 6:35 PM Go to last post
    Paul F Franklin

    New Lee Valley Web Site

    Thread Starter: Paul F Franklin

    Seems the roll out of the new site is not going completely smoothly. Have been trying to place an order all morning and the site just spins when I try to checkout. Tried a few different browsers too. Guess I may have to call :eek: New site design seems nice and clean though but it will take...

    Last Post By: Aaron Rosenthal Yesterday, 9:44 PM Go to last post
    Alan Lightstone

    High CRI Workshop LEDs

    Thread Starter: Alan Lightstone

    I've been spending tons of time looking for high CRI (>90, hopefully 93-95) LED bulbs / fixtures for my workshop build. I'm having a real tough time finding LED tube fixtures with high CRIs (looking for 4000-4100K fixtures). I can find Edison base bulbs or floods with high CRIs, but linear...

    Last Post By: Jay Champagne Yesterday, 8:36 PM Go to last post
    Ronald Blue

    Two Year Old Camaster Stinger III

    Thread Starter: Ronald Blue

    I have a locally available Camaster Stinger III. It's a 4 X 8 machine with a three head setup. Whats the benefit of the three head arrangement? Is it an alternative to an ATC system? What's a fair price? He says it was $18,000 new. He's discounted it a lot from that amount. Nearly half. He did say...

    Last Post By: David Buchhauser Yesterday, 9:35 PM Go to last post
    Tom Trees

    Suitable relay for three wire control on a VFD

    Thread Starter: Tom Trees

    Hello folks I have been walking through the steps with another forum member on setting up a VFD for his saw. Unfortunately the VFD does not have a relay OR COMMON for three wire control/push button station. Can any of you guys point me in the right direction to find a suitable relay for him? ...

    Last Post By: David Buchhauser Yesterday, 9:43 PM Go to last post
  • Mac Cambra

    There is no available content written by Mac Cambra
  • Recent Polls

  • Recent Forum Posts

    Bert Kemp

    Split image in corel

    Thanks Kev I'll see if I can do it that way to. just to learn a new method

    Bert Kemp Today, 1:14 AM Go to last post
    Davis Young

    Glue to attach pine to metal?

    He needs to run a frame the same thickness as the battens along the perimeter of the metal. Screw the frame into the metal. Then pocket hole the battens

    Davis Young Today, 1:12 AM Go to last post
    Bert Kemp

    Getting photos off old hard drive

    OK I'm gonna order one and see if it works thanks for all the help I'll let ya know how I did

    Bert Kemp Today, 1:10 AM Go to last post
    Stew Denton

    Nicholson workbench


    My main bench is small. It is a plank setup on saw horses. One set of heavy planks screwed together is about 4' long, but heavy,

    Stew Denton Today, 12:56 AM Go to last post
    Guy Donham

    Gum Wood

    I have been given some wood called red gum. I used it to make a jewelry box and turned some pens. The wood is beautiful. The tree we have here in east

    Guy Donham Today, 12:41 AM Go to last post
  • Recent Blog Posts