Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Time for some levity
Thread Starter: Dave Anderson NH
With all of the negativity and political stuff going on with the Covid-19 virus it is time to look at the humorous side of things. Feel free to add more, but keep it clean or it will be deleted.
Last Post By: Dave Zellers Today, 9:10 PM

How to replace Syder/Coupler on Supermax 16/32>?
Thread Starter: Thomas Colson
I have a Supermax 16/32 with a pretty clapped out rubber spyder-coupler. Little tiny pieces of rubber are coming out of it, which makes sense, I've used this like I stole it for the last 2 years. Any videos or instructions with pictures anywhere on how to do this that are deliberately hidden and...
Last Post By: Jerry Bruette Today, 4:13 PM

Help Me Pick a Plow Plane or Is It a Plough Plane
Thread Starter: Thomas McCurnin
Typical use will be on 3/4 to 7/8" stock planing on edge for a a 1/4" groove about 3/8" deep for frame and panel construction. I'll also be using it for grooving a post, usually about 1.5" x 1.5" is typical, again to accept a panel for frame and panel construction. It needs to go both directions,...
Last Post By: Derek Cohen Today, 7:45 PM

I hate rusty saws, but...
Thread Starter: Richard Hutchings
I just saw an ad for 7 rusty saws for $25 and I may not be able to resist. One has the thumbhole but broken horn. It might be worth buying the whole lot but I'll have to get better at cleaning them up. I hate the mess. Hopefully someone will buy them before I decide to bite the bullet.
Last Post By: Maurice Mcmurry Today, 9:51 AM

VFD for 7.5 hp 3 phase to run on 220 single phase
Thread Starter: Mike Leiferman
Anyone with any experience running a 7.5 hp 220 volt 26 amp 3 phase from a VFD powered by 220 single phase? I would like to know a) what specific vfd you are using if you recommend it, b) any issues I should be aware of The motor is driving a 1995 Lazzari Tema 3000i. The alternative for me...
Last Post By: Matt Day Today, 8:58 PM

Solid Walnut bookshelf dados - is glue enough?
Thread Starter: Bill Brammer
Building 6 ft high, 28 in wide, 12 inch deep solid 3/4 inch walnut bookshelf , no adjustable shelves. I have dados for all shelves. The sides are a little bowed, requiring some pressure with clamps to pull them together with the dados. Not a ton, but some. I'm trying to decide if I need to add...
Last Post By: Jim Becker Today, 10:58 AM

Joe Bailey

There is no available content written by Joe Bailey

Recent Polls
Recent Forum Posts

Polyaspartic Garage Floor Coating?

I have done a several DIY epoxy garage floor coatings from various stores for several Clients. They are OK and I was able to cut the cost way down compared
Maurice Mcmurry Today, 9:40 PM

Anyone have experience with Sheds Unlimited?

City doesn’t allow post frame construction unless I have five or more acres. I have three acres. The real issue with post frame I think is the
Brian Elfert Today, 9:32 PM

Options for Harvey Table Saw?

Buy the SawStop and keep your fingers, simple as that. If people who have been operating table saws for decades like Jimmy Diresta can hurt themselves,
Andrew More Today, 9:31 PM

Kitchen Cabinet Refinishing - DIYer can't decide on materials

Jim, thank you.
Lonnie Gallaher Today, 9:29 PM

Time for some levity

"I once shot a man just to watch him pee"

OMG I love when stories like these roll around every once in a while.

This
Dave Zellers Today, 9:10 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Joe Bailey

Recent Polls

Recent Forum Posts

Recent Blog Posts