Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Time for some levity
Thread Starter: Dave Anderson NH
With all of the negativity and political stuff going on with the Covid-19 virus it is time to look at the humorous side of things. Feel free to add more, but keep it clean or it will be deleted.
Last Post By: Dave Zellers Yesterday, 9:10 PM

Shop Build...should be a fun journey...
Thread Starter: Jim Becker
I debated about starting this thread now or later, but decided on now because, well...I might forget something. :o As a little background, at our previous property, I was blessed with a reasonably sized, fully conditioned space for my shop in what was originally a three-and-a-half vehicle garage...
Last Post By: glenn bradley Today, 9:45 AM

VFD for 7.5 hp 3 phase to run on 220 single phase
Thread Starter: Mike Leiferman
Anyone with any experience running a 7.5 hp 220 volt 26 amp 3 phase from a VFD powered by 220 single phase? I would like to know a) what specific vfd you are using if you recommend it, b) any issues I should be aware of The motor is driving a 1995 Lazzari Tema 3000i. The alternative for me...
Last Post By: Jared Sankovich Today, 10:04 AM

Help Me Pick a Plow Plane or Is It a Plough Plane
Thread Starter: Thomas McCurnin
Typical use will be on 3/4 to 7/8" stock planing on edge for a a 1/4" groove about 3/8" deep for frame and panel construction. I'll also be using it for grooving a post, usually about 1.5" x 1.5" is typical, again to accept a panel for frame and panel construction. It needs to go both directions,...
Last Post By: steven c newman Today, 3:11 AM

How to replace Syder/Coupler on Supermax 16/32>?
Thread Starter: Thomas Colson
I have a Supermax 16/32 with a pretty clapped out rubber spyder-coupler. Little tiny pieces of rubber are coming out of it, which makes sense, I've used this like I stole it for the last 2 years. Any videos or instructions with pictures anywhere on how to do this that are deliberately hidden and...
Last Post By: Jerry Bruette Yesterday, 4:13 PM

Cost effectiveness of a slider vs. tracksaw & tablesaw
Thread Starter: Jonathan Jung
I thought about posting this to the business section, because I'd really like input from professionals who use their shop as a business. For those of you who make $ or even a living making furniture or cabinets, how long does it take for a sliding table saw to pay for itself compared to a track saw...
Last Post By: Kevin Jenness Today, 9:49 AM

glenn bradley

There is no available content written by glenn bradley

Recent Polls
Recent Forum Posts

Polyaspartic Garage Floor Coating?

Thank you. That's very helpful.
Pat Germain Today, 10:44 AM

Options for Harvey Table Saw?

It's all good. I haven't ruled out a SawStop, but right now I'm looking for information about the Harvey.
Pat Germain Today, 10:42 AM

Water heater anode school please

Not sure if this could be the problem, but sometimes an engineer will throw in a left hand thread just to mess with people.

Or some idiot
Jim Koepke Today, 10:39 AM

cub cadet older LTX-1142 Hydrastatic, start issue

thanks on both. Makes total sense as a starting point. Bit hard to explain well as it was still trying to turn over that is it was moving a bit just
Warren Lake Today, 10:15 AM

Options for Harvey Table Saw?

Funny how they always seem to pop up with an answer to a question that wasn't asked isn't it?
Dave Sweeney Today, 10:12 AM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

glenn bradley

Recent Polls

Recent Forum Posts

Recent Blog Posts