• Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Dave Anderson NH

    Time for some levity

    Thread Starter: Dave Anderson NH

    With all of the negativity and political stuff going on with the Covid-19 virus it is time to look at the humorous side of things. Feel free to add more, but keep it clean or it will be deleted.

    Last Post By: Jim Allen Today, 12:57 PM Go to last post
    Michael Drew

    Relocating: South Dakota?

    Thread Starter: Michael Drew

    I am hoping there might be some SD residents here, or maybe others who know the state? I'm sorting through my options of finding a suitable place to relocate to and retire within the next 24 months. I have lived all over the country, but my driver's license has been AK since I first got it. I...

    Last Post By: Kyle Stiefel Today, 12:14 PM Go to last post
    Jack Frederick

    Internet advice

    Thread Starter: Jack Frederick

    I live in a third world country, meaning E of I-5 in CA. We currently have AT&T for our ISP and they guarantee all the way up to, but not over 3mbps. I am fixin to get the Starlink system. Some in the area have done so and report great results. My problem is that the house is surrounded by two 4+í...

    Last Post By: Zachary Hoyt Today, 2:32 PM Go to last post
    Phillip Mitchell

    What grit do you normally start sanding at after milling?

    Thread Starter: Phillip Mitchell

    I know this is vague and depends but... Iím curious what grit others start their sanding routine at after milling? The planer is typically always the last step on both faces and edges unless the stock is wider than 9Ē, in which case I canít feed it on edge through my planer and will rip to width...

    Last Post By: Phillip Mitchell Today, 2:15 PM Go to last post
    Nick Roznak

    Plane Sharpening Issues

    Thread Starter: Nick Roznak

    I've read numerous threads on this forum but this is my first post! I am sharpening the irons for three planes which I recently acquired. These are all Stanley Type 13 with Sweetheart irons. Right now I am working at getting a primary bevel using a diamond plate and a honing guide. All of the...

    Last Post By: steven c newman Yesterday, 7:31 PM Go to last post
    Tom Bender

    Dog Attack

    Thread Starter: Tom Bender

    There are dogs in the world and sometimes they attack. That is not going to change. So here is my question. If I have no weapons and no objects within reach how can I best defend myself? Maybe the martial arts have something to offer.

    Last Post By: Warren Lake Today, 2:33 PM Go to last post
  • Kevin Jenness

    There is no available content written by Kevin Jenness
  • Recent Polls

  • Recent Forum Posts

    Chris McCapherey

    New Fuji Q4 owner - what finish to spray??

    Thanks all, target coatings order just arrived today. So for spraying the shellac I have a 1.0,1.5, and 1.8 nozzle. Is that what you reference when

    Chris McCapherey Today, 3:08 PM Go to last post
    Warren Lake

    Poplar

    if I make an old piece ill use poplar over soft maple as it will have an older and less clinical look to it.

    Warren Lake Today, 2:51 PM Go to last post
    Mark Rainey

    Another chair

    knee blocks attached to legs using hot hide glue - used a rub joint because I could not see an easy way to clamp

    Mark Rainey Today, 2:34 PM Go to last post
    Warren Lake

    Dog Attack

    I was kidding about the sit thing. James Bond Movie came to mind where during a possible lion attack he says sit and it does.

    Thanks for

    Warren Lake Today, 2:33 PM Go to last post
    Zachary Hoyt

    Internet advice

    Our current DSL internet at the farm is slow. I just ran a speed test and got 2.21 mbps download and .76 up. I've signed up for fiber-optic at the new

    Zachary Hoyt Today, 2:32 PM Go to last post
  • Recent Blog Posts