Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Time for some levity
Thread Starter: Dave Anderson NH
With all of the negativity and political stuff going on with the Covid-19 virus it is time to look at the humorous side of things. Feel free to add more, but keep it clean or it will be deleted.
Last Post By: Dave Zellers Yesterday, 9:10 PM

Shop Build...should be a fun journey...
Thread Starter: Jim Becker
I debated about starting this thread now or later, but decided on now because, well...I might forget something. :o As a little background, at our previous property, I was blessed with a reasonably sized, fully conditioned space for my shop in what was originally a three-and-a-half vehicle garage...
Last Post By: Jim Becker Today, 8:54 AM

VFD for 7.5 hp 3 phase to run on 220 single phase
Thread Starter: Mike Leiferman
Anyone with any experience running a 7.5 hp 220 volt 26 amp 3 phase from a VFD powered by 220 single phase? I would like to know a) what specific vfd you are using if you recommend it, b) any issues I should be aware of The motor is driving a 1995 Lazzari Tema 3000i. The alternative for me...
Last Post By: Mike Leiferman Today, 8:59 AM

Help Me Pick a Plow Plane or Is It a Plough Plane
Thread Starter: Thomas McCurnin
Typical use will be on 3/4 to 7/8" stock planing on edge for a a 1/4" groove about 3/8" deep for frame and panel construction. I'll also be using it for grooving a post, usually about 1.5" x 1.5" is typical, again to accept a panel for frame and panel construction. It needs to go both directions,...
Last Post By: steven c newman Today, 3:11 AM

How to replace Syder/Coupler on Supermax 16/32>?
Thread Starter: Thomas Colson
I have a Supermax 16/32 with a pretty clapped out rubber spyder-coupler. Little tiny pieces of rubber are coming out of it, which makes sense, I've used this like I stole it for the last 2 years. Any videos or instructions with pictures anywhere on how to do this that are deliberately hidden and...
Last Post By: Jerry Bruette Yesterday, 4:13 PM

I hate rusty saws, but...
Thread Starter: Richard Hutchings
I just saw an ad for 7 rusty saws for $25 and I may not be able to resist. One has the thumbhole but broken horn. It might be worth buying the whole lot but I'll have to get better at cleaning them up. I hate the mess. Hopefully someone will buy them before I decide to bite the bullet.
Last Post By: Maurice Mcmurry Yesterday, 9:51 AM

Kevin Jenness

There is no available content written by Kevin Jenness

Recent Polls
Recent Forum Posts

Polyaspartic Garage Floor Coating?

I paid $4.5 per square foot. They ground the floor first then put down one or two (I can't remember) coats of color, then 100% chip coverage and finally
Leigh Betsch Today, 9:14 AM

Seeking VFD Advice

Agree with Michael on the power switch. And if you get a DPDT switch it can protect your VFD from lightning if the strike is not too hot.

Tom Bender Today, 9:10 AM

Anyone have experience with Sheds Unlimited?

That's short sighted on their part and very sad. Also, post frame structures are not limited to metal siding and roofing. They can be finished with whatever
Jim Becker Today, 9:04 AM

VFD for 7.5 hp 3 phase to run on 220 single phase

Malcolm
Thanks for taking time to provide this clear and detailed response!
The parameters that allow remote operation (turn off the keypad)
Mike Leiferman Today, 8:59 AM

Kitchen Cabinet Refinishing - DIYer can't decide on materials

Maurice, the equivalent to the 100% acrylic Impervo from SW is ProClassic.
Jim Becker Today, 8:58 AM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Kevin Jenness

Recent Polls

Recent Forum Posts

Recent Blog Posts