• Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Michael Arruda

    Home Depot return policy change without notification

    Thread Starter: Michael Arruda

    Hello all, I had some small items left over from various things I've done around the house recently and decided to gather them up to take back to Home Depot. These items were purchased at various times over the past couple weeks and I of course misplaced my receipts. Meaning they got washed,...

    Last Post By: Doug Dawson Today, 7:19 PM Go to last post
    John McGovern

    Table Saw Questions

    Thread Starter: John McGovern

    Hi All, I've been lurking in the weeds for some time and have found this venue to be the most knowledgeable, helpful, and courteous forum on the block. And, I know this question has been asked and answered so many times, but I hope you all have the patience for one more dip to the well to answer...

    Last Post By: Thomas McCurnin Today, 7:24 PM Go to last post
    Paul F Franklin

    New Lee Valley Web Site

    Thread Starter: Paul F Franklin

    Seems the roll out of the new site is not going completely smoothly. Have been trying to place an order all morning and the site just spins when I try to checkout. Tried a few different browsers too. Guess I may have to call :eek: New site design seems nice and clean though but it will take...

    Last Post By: Jim Koepke Today, 10:30 AM Go to last post
    Carl Beckett

    Dust collection barrel

    Thread Starter: Carl Beckett

    What is everyone using for a dust collection barrel? I have a heavy duty plastic trash can I put a gasket on. But it 'implodes' at times. Before I go messing with reinforcement, maybe I should just ditch it all together for something more suitable (ideally cheap and readily available locally). ...

    Last Post By: Tom Bender Today, 5:15 PM Go to last post
    Carl Beckett

    Tablesaw dust collection hood

    Thread Starter: Carl Beckett

    Well, after a weekend working with black walnut I have GOT to improve my tablesaw dust collection. Which means time to put the blade guard/collection hood at the top of the project list. The support arm will be home made. The guard/hood can be either home made or purchased, but since I want to...

    Last Post By: Tom Bender Today, 7:23 PM Go to last post
    Tom Trees

    Suitable relay for three wire control on a VFD

    Thread Starter: Tom Trees

    Hello folks I have been walking through the steps with another forum member on setting up a VFD for his saw. Unfortunately the VFD does not have a relay OR COMMON for three wire control/push button station. Can any of you guys point me in the right direction to find a suitable relay for him? ...

    Last Post By: William Chain Today, 8:07 PM Go to last post
  • Howard Pollack

    There is no available content written by Howard Pollack
  • Recent Polls

  • Recent Forum Posts

    Rob Luter

    Sharpening Help?

    Thanks for all the suggestions. I went to school and managed to put razor edges on everything.

    Here's about 90 minutes worth of work on air

    Rob Luter Today, 8:10 PM Go to last post
    William Chain

    Suitable relay for three wire control on a VFD

    Ok - my VFD is a cheaper model, Isacon or Askpower. The trigger to turn the motor on and off is a simple matter of closing a circuit between a lug marked

    William Chain Today, 8:07 PM Go to last post
    Thomas Canfield

    "Shifting Meridian"

    You have a lot going on there and it looks like it all came together well. The segments, open segments, layer ring, diagonal sections, and top carving.

    Thomas Canfield Today, 8:06 PM Go to last post
    Thomas McCurnin

    liquid hide glue

    Ditto as to what Robert said. Old Brown Hide Glue really cannot be used right out of the bottle. It needs to be warmed up between 100-140 degrees.

    Thomas McCurnin Today, 8:04 PM Go to last post
    Carl Beckett

    Vacuum Fence for Slider

    Beautiful boxes! I would love to see more posts of your work (in the project section?)

    Carl Beckett Today, 7:55 PM Go to last post
  • Recent Blog Posts