• Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Dave Anderson NH

    Time for some levity

    Thread Starter: Dave Anderson NH

    With all of the negativity and political stuff going on with the Covid-19 virus it is time to look at the humorous side of things. Feel free to add more, but keep it clean or it will be deleted.

    Last Post By: William Lessenberry Yesterday, 11:34 PM Go to last post
    Dave Fritz

    grab hook or slip hook

    Thread Starter: Dave Fritz

    I'm looking at getting a pair of bucket hooks: https://www.bxpanded.com/BX-bucket-hooks I like the fact they can be removed when not needed. I will use it mostly for lifting logs and pulling them out of the woods as well as sometimes lifting heavy items. Most of the time I'll use a chain which...

    Last Post By: Edward Weber Yesterday, 3:16 PM Go to last post
    Leigh Betsch

    Paint booth fan?

    Thread Starter: Leigh Betsch

    I am converting my downdraft sanding table to a duel purpose downdraft/paint booth. Basically I have a 3'x5' downdraft bench on wheels with an old furnace blower to draw the sanding dust thru the table and out thru furnace filters. With my sander hooked to my Festool dust extractor, it does a...

    Last Post By: Leigh Betsch Yesterday, 8:04 PM Go to last post
    Doug Walls

    SawStop PCS 1.75HP Questions

    Thread Starter: Doug Walls

    I finally bit the bullet & ordered a SawStop PCS 1.75HP with the 36" T-Glide-Fence the other day from my local Woodcraft store just before the May 3rd. price increase. I really wanted to get the 3HP. model, but I only have one 30-amp 240V circuit available & my dust collector is currently run...

    Last Post By: Jim Dwight Yesterday, 9:39 AM Go to last post
    Thomas McCurnin

    Help Me Pick a Plow Plane or Is It a Plough Plane

    Thread Starter: Thomas McCurnin

    Typical use will be on 3/4 to 7/8" stock planing on edge for a a 1/4" groove about 3/8" deep for frame and panel construction. I'll also be using it for grooving a post, usually about 1.5" x 1.5" is typical, again to accept a panel for frame and panel construction. It needs to go both directions,...

    Last Post By: Tom M King Yesterday, 10:05 PM Go to last post
    Richard Hutchings

    I hate rusty saws, but...

    Thread Starter: Richard Hutchings

    I just saw an ad for 7 rusty saws for $25 and I may not be able to resist. One has the thumbhole but broken horn. It might be worth buying the whole lot but I'll have to get better at cleaning them up. I hate the mess. Hopefully someone will buy them before I decide to bite the bullet.

    Last Post By: Maurice Mcmurry Yesterday, 5:46 PM Go to last post
  • John TenEyck

    There is no available content written by John TenEyck
  • Recent Polls

  • Recent Forum Posts

    William Lessenberry

    Time for some levity

    Folks in south-central Arkansas are good shots. Lots of hunters down there. Mayor says it'll cost around $100,000 to fix the water tower. Don't know

    William Lessenberry Today, 11:34 PM Go to last post
    William Lessenberry

    Water leaking under slab

    We found another company to check out the problem. Had a van full of sophisticated looking equipment that they used to trace where the water line was

    William Lessenberry Today, 11:20 PM Go to last post
    Aaron Liebling

    Legs for a midcentury bench

    I cut a few on the table saw and got a nice consistent 1/32" after sanding..that said, it was VERY wasteful of wood 91/8" kerf). I found a

    Aaron Liebling Today, 11:07 PM Go to last post
    sean meltvedt

    Sawstop Rails



    36” rails with the left extension removed gives you an approximate 48” rip capacity. This saw was damaged and the left side

    sean meltvedt Today, 10:56 PM Go to last post
    Eric Arnsdorff

    AFS1000 Jet Air Filter doesn't work

    James I had an issue with the remote and found it was the buttons. I posted details of the fix here at SMC some time back. The buttons are a standard

    Eric Arnsdorff Today, 10:44 PM Go to last post
  • Recent Blog Posts