Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Time for some levity
Thread Starter: Dave Anderson NH
With all of the negativity and political stuff going on with the Covid-19 virus it is time to look at the humorous side of things. Feel free to add more, but keep it clean or it will be deleted.
Last Post By: Dave Zellers Today, 9:10 PM

VFD for 7.5 hp 3 phase to run on 220 single phase
Thread Starter: Mike Leiferman
Anyone with any experience running a 7.5 hp 220 volt 26 amp 3 phase from a VFD powered by 220 single phase? I would like to know a) what specific vfd you are using if you recommend it, b) any issues I should be aware of The motor is driving a 1995 Lazzari Tema 3000i. The alternative for me...
Last Post By: Mike Leiferman Today, 11:24 PM

How to replace Syder/Coupler on Supermax 16/32>?
Thread Starter: Thomas Colson
I have a Supermax 16/32 with a pretty clapped out rubber spyder-coupler. Little tiny pieces of rubber are coming out of it, which makes sense, I've used this like I stole it for the last 2 years. Any videos or instructions with pictures anywhere on how to do this that are deliberately hidden and...
Last Post By: Jerry Bruette Today, 4:13 PM

Help Me Pick a Plow Plane or Is It a Plough Plane
Thread Starter: Thomas McCurnin
Typical use will be on 3/4 to 7/8" stock planing on edge for a a 1/4" groove about 3/8" deep for frame and panel construction. I'll also be using it for grooving a post, usually about 1.5" x 1.5" is typical, again to accept a panel for frame and panel construction. It needs to go both directions,...
Last Post By: Derek Cohen Today, 7:45 PM

I hate rusty saws, but...
Thread Starter: Richard Hutchings
I just saw an ad for 7 rusty saws for $25 and I may not be able to resist. One has the thumbhole but broken horn. It might be worth buying the whole lot but I'll have to get better at cleaning them up. I hate the mess. Hopefully someone will buy them before I decide to bite the bullet.
Last Post By: Maurice Mcmurry Today, 9:51 AM

Cost effectiveness of a slider vs. tracksaw & tablesaw
Thread Starter: Jonathan Jung
I thought about posting this to the business section, because I'd really like input from professionals who use their shop as a business. For those of you who make $ or even a living making furniture or cabinets, how long does it take for a sliding table saw to pay for itself compared to a track saw...
Last Post By: Mike Wilkins Today, 11:16 PM

John TenEyck

There is no available content written by John TenEyck

Recent Polls
Recent Forum Posts

VFD for 7.5 hp 3 phase to run on 220 single phase

It is a single phase input, 3 phase output. The motor is about 7.5 hp, the vfd is rated at 10 hp.
Mike Leiferman Today, 11:24 PM

Shelves? In dire need of lots of storage space...

Correct. My room is very roughly 5x3 meters. Actually a little less because it's not rectangular. Really tiny!

Other rooms are larger, and
Luke Dupont Today, 11:22 PM

VFD for 7.5 hp 3 phase to run on 220 single phase

Is it a 10hp 3ph vfd? You need to double the size of a 3ph vfd run on single phase. As an example the fugi 60amp vfd (20hp) only outputs 27a on single
Jared Sankovich Today, 11:17 PM

Cost effectiveness of a slider vs. tracksaw & tablesaw

I have watched several YouTube videos by an English woodworker named Peter Millard with the 10 minute workshop. He has completed several large case builds
Mike Wilkins Today, 11:16 PM

possible wiring diagram

attached possible wiring diagram for remote stop start for Vevor vfd in lieu of original panel controls

suggestions advice appreciated
Mike Leiferman Today, 11:13 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

John TenEyck

Recent Polls

Recent Forum Posts

Recent Blog Posts