Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

How to bend wood like this - Outdoor furniture project
Thread Starter: Alan Lightstone
Looking for a new project to do. I've been spending a few months upgrading the workshop / fixing minor annoyances, and really need to actually build something. I ran across this in a magazine ad. The furniture is supposedly solid teak, though I don't think that will be in the cards for...
Last Post By: Mike King Today, 11:18 AM

Cheap Bandsaw for Resawing
Thread Starter: Jimmy Harris
I'm a hobbyist on a limited budget looking for a bandsaw, primarily for resawing. Let's say, 12" of 8/4 hard maple cut down the middle would be the maximum I would ever ask of it. I'm under the impression that I'll need a steel framed bandsaw for that. What else do I need to know? Are guides...
Last Post By: Sam Force Today, 9:43 AM

Are they building standalone car washes like crazy in your area too?
Thread Starter: Brian Elfert
They are going crazy building standalone car washes in my area. I know of at least three currently under construction nearby, and a few others that recently opened. Car washes are going up all over the Minneapolis metro area. There will easily be three times as many standalone car washes once...
Last Post By: Jim Becker Yesterday, 8:10 PM

Epoxy glue joint opened
Thread Starter: Mark Gibney
I glued up this oval Santos mahogany coffee table on Sunday. Yesterday morning, Tuesday, I placed it outside under cloudy skies in the hope that the UV to hasten the darkening of wood surface before finishing later this week. The center seam opened up. I used brand new T-88 epoxy with...
Last Post By: Mark Gibney Yesterday, 6:33 PM

landscaping is my other hobby, record for me, 25 yards of mulch
Thread Starter: Brian Runau
My landscape guys clean up the beds and install mulch for me now, too old, but I planted everything you see except the very large mature trees. Shade garden, cutting garden, front. Thanks Brian
Last Post By: julian abram Yesterday, 8:32 PM

Vectric Software V12 Now Available
Thread Starter: Michael Burnside
I was talking with friend over the weekend and they were unaware that V12 has been released. So, I figured I would post here in case someone wasn't aware of this news. In general the upgrades look good overall. I personally upgraded my version of Vcarve Pro.
Last Post By: Grant Wilkinson Yesterday, 12:08 PM

Bruce Wrenn

There is no available content written by Bruce Wrenn

Recent Polls
Would you borrow a tool from someone? (Votes: 71)

Sure - why not? (Votes: 9)

Never. If I needed something, I'd buy or rent it. (Votes: 10)

Maybe. Depends on the person and the tool. (Votes: 52)
Recent Forum Posts

Gable Vent

Does anyone have a design for an 18" octane gable vent?
I am looking for the angle and size of the louvers.
I am installing an attic
Mike Hanan Today, 11:19 AM

How to bend wood like this - Outdoor furniture project

An alternate way to achieve the curve would be to Cooper the bend. But rather than grain following the curve, the grain would be vertical (I don't think
Mike King Today, 11:18 AM

climatis experts

ILl have to check and see when I did put it in for sure. Times flies and the one that died is coming back. I either have to leave the left one that
Warren Lake Today, 11:11 AM

lap tops in coffee shops

there would be no bills only checking my email when im away or googling directions. I did read about VPN's after posting. One friend was hacked while
Warren Lake Today, 11:09 AM

cleaning a tomb stone

there used to be a place right in the area so ill check and see if its still there and ask them.
Warren Lake Today, 11:06 AM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Bruce Wrenn

Recent Polls

Recent Forum Posts

Recent Blog Posts