• Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Kev Williams

    Had the most pleasant shopping experience yesterday--

    Thread Starter: Kev Williams

    Needed to go to Walmart for a few things. They implemented a mandatory mask rule last weekend. When I pulled into the parking lot first thing I noticed was there was barely half as many cars than normal, maybe less. The south doors were locked, entry/exit from the north doors only. Went in, grabbed...

    Last Post By: Malcolm McLeod Yesterday, 5:20 PM Go to last post
    Victor Price Jr

    Hand Plane - First time buying

    Thread Starter: Victor Price Jr

    Hi Everyone, this is my first post and hopefully I can get some advice. I've primarily been woodworker who uses machines, but I'm find that I need more options. I'm planning on buying a few hand planes in the near future, and I'd like some opinions. I like to buy a tool once, and keep it, so I...

    Last Post By: Thomas Wilson Today, 12:56 PM Go to last post
    Lisa Starr

    Help me choose new ROS-please

    Thread Starter: Lisa Starr

    Well, my Dewalt ROS (DWC6421) has died. I've been perfectly happy with it and it owes me nothing. That said, I'd like your thoughts before purchasing a new one. I'd like to stay under $200 and have some other wishes. 1) Uses 5" discs, hook & loop, as I have lots of stock. 2) Reasonably...

    Last Post By: Michael Drew Today, 12:34 PM Go to last post
    ken hatch

    More on Unicorn Profile

    Thread Starter: ken hatch

    I'm still crippling around on a bad wheel so not much is happening in the shop even sharpening is too much some days. There have been a few days where whisky and a elevated foot was all I could do. On one of the good days I did install a stitched cotton wheel on the grinder and have taken a...

    Last Post By: ken hatch Yesterday, 11:24 PM Go to last post
    Rich Riddle

    Vintage Cars

    Thread Starter: Rich Riddle

    The wife's 1956 Ford Thunderbird will be delivered next week from the body shop (since January 2019). When it arrives, the wife's 1965 Mustang heads down to be restored (going from blue to white). She won't restore her old 1991 Ford F150 though. She might look for a 1960's vintage Camaro soon. What...

    Last Post By: Michael Weber Today, 11:34 AM Go to last post
    Bruce Wrenn

    Bragging on USPS

    Thread Starter: Bruce Wrenn

    Ordered a fuel pump for my 1988 Mitsubishi Mighty Max from Rock Auto Parts on Tuesday afternoon (3:30 PM, EDT.) Shipped USPS. Today (Thursday) at 3:30 PM, fuel pump was delivered. Original shipping warehouse is in CA. Two days from west coast to east coast isn't bad, especially for standard...

    Last Post By: Bruce Wrenn Yesterday, 8:45 PM Go to last post
  • Ron Citerone

    There is no available content written by Ron Citerone
  • Recent Polls

    Which fence: (Votes: 9)

    1. Delta Biesemeyer 78919B Type 2 (Votes: 0)

    2. SawStop TGP2-FA (Votes: 5)

    3. Something else (Votes: 4)

  • Recent Forum Posts

    Prashun Patel

    Dining table - mixed woods

    Imho you will have an easier time and more consistent product by sticking With one wood. Either wood will be fine. Red oak is easier to stain. My

    Prashun Patel Today, 1:18 PM Go to last post
    Mark Bolton

    Do you buy lumber S2S?

    In my area at least there is no option for "finish" planed period other than the home center which I think is what the majority of people think

    Mark Bolton Today, 1:12 PM Go to last post
    Bob Hinden

    Do you buy lumber S2S?

    I like to mill it myself because it gives me control over the final thickness. I am not limited to what I can buy S2S, and I can ensure that all of

    Bob Hinden Today, 1:12 PM Go to last post
    Dan Rude

    SawStop Base not going down

    Since you have the Mechanical base, you might have something lodged between the pedals. The pin might have popped out on the release foot or the spring

    Dan Rude Today, 1:10 PM Go to last post
    John Ziebron

    Dining table - mixed woods

    I think I've procrastinated enough on building my new dining table and now that I have A/C in my pole barn workshop I'm ready to go. The basic design

    John Ziebron Today, 1:09 PM Go to last post
  • Recent Blog Posts