Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Vintage Martin T75 restoration
Thread Starter: Patrick Walsh
So I have a opportunity to purchase the above machine for a fair deal from my employer. I am aware of the phenolic guides being pop riveted I the the sliding table along with not availible for replacement. So my question is as follows to those in the know with regard to the phenolic ways....
Last Post By: Bradley Gray Today, 11:34 AM

Share funny pictures here
Thread Starter: Malcolm Schweizer
I love these kinds of things. Make me laugh today and share your favorites.
Last Post By: Frederick Skelly Today, 2:14 PM

Drill Press Table
Thread Starter: Derek Cohen
A couple of weeks ago I took advantage of a Black Friday sale and purchased a Nova Voyager drill press for a great discount. This replaced a Taiwanese model I had for 25 years. Yeah, I know this machine is OTT, but it is an amazing tool. For those who are not familiar with the Voyager, it is a...
Last Post By: Doug Dawson Today, 2:28 PM

19 year snow blower dead - I don't think anything new will last as long
Thread Starter: Brian Elfert
My 19 year old Troy-Bilt snow blower is dead. A bearing support for the auger broke and no longer available. This was one of the last units made before Gardenway went bankrupt. This is not an MTD. This thing is a tank. It broke a few years back and the hardware store I bought it from said to...
Last Post By: Brian Elfert Today, 11:15 AM

Shaving
Thread Starter: Bert Kemp
Well I use to shave everyday and get my blades from an online shave club. Over the last year or so since I don't get out as much I find I don't shave everyday sometimes I let it got for 2 or 3 days. Then I find my dbl blade razors don't do the job they get clogged up pretty quick and hard to rinse...
Last Post By: Chris Damm Today, 9:54 AM

Mounting UHMW Sheet To Fence
Thread Starter: Robert Stanton
1. I've purchased a 1/4" sheet of UHMW to attach to my 80/20 fence. How often should I drill mounting holes? I have 4 nuts and probably need more (they aren't cheep). 2. The UHMW sheet has tool marks on it. I expected it to be smooth and perhaps glossy. I'm not sure this photo will matter but...
Last Post By: Michael A. Tyree Yesterday, 6:05 PM

Bob Turkovich

There is no available content written by Bob Turkovich

Recent Polls
Do you still have a Sears store close to home? (Votes: 41)

YES (Votes: 12)

NO (Votes: 29)
Recent Forum Posts

Helical head for 8" jointer?

I have been using a PM60 8" jointer for years, straight blades seem to be working just fine for me. But, whatever fits your budget. Randy
Randall J Cox Today, 4:42 PM

Gone metric?

Know this has been cussed and discussed over the years on all woodworking forums.... With that said, I convert to metric for lots of stuff, use Siri
Randall J Cox Today, 4:39 PM

Articulated arm for a small folding shelf?

Thank you everyone. Lots of good hardware out there!
Mark Gibney Today, 4:31 PM

Cell Phone

My ZTE android phone has an 'ultra power save mode' that will make the battery last for at least 4 days. That shuts off the bluetooth, wifi, GPS and background
Tom Stenzel Today, 4:25 PM

Suggestions for a low angle block plane

I've bought 60 1/2s on ebay for under $30 in good condition. Never buy one unless the photos show the mouth without defects and an assurance from the
Corey Rebette Today, 4:24 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Bob Turkovich

Recent Polls

Recent Forum Posts

Recent Blog Posts