Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Time for some levity
Thread Starter: Dave Anderson NH
With all of the negativity and political stuff going on with the Covid-19 virus it is time to look at the humorous side of things. Feel free to add more, but keep it clean or it will be deleted.
Last Post By: Jim Koepke Today, 3:25 PM

Milling machine as a mortiser
Thread Starter: andrew whicker
Hi all, I don't look often, but when I do it seems there are absolutely no used mortising machines out there. Something I've always wanted (someday) was a knee mill. There's a place near me that has had a Cincinnati Contour Master for sale forever (years and years). They re build these...
Last Post By: Wes Grass Today, 10:51 PM

Dumb answers to dumb questions
Thread Starter: Zachary Hoyt
I used to feel frustrated when I would have listed something for sale on Craigslist or Facebook and included the town where I lived, and instead of looking it up on their devices people would write to me to ask "where is Orwell" (where I used to live) or now "where is Piercefield?". I finally...
Last Post By: Cameron Wood Today, 10:21 PM

Recommendations for sailboat for novice sailors
Thread Starter: Andrew Nemeth
Hello, I’m looking for advice and recommendations for a good plan or kit to construct a sailboat for a novice crew. My 10yo daughter went to sailing camp last summer and had a blast. It was a skills based camp that eventually leads to racing and ASA certification. They used what appeared to...
Last Post By: Maurice Mcmurry Today, 10:39 AM

Are they building standalone car washes like crazy in your area too?
Thread Starter: Brian Elfert
They are going crazy building standalone car washes in my area. I know of at least three currently under construction nearby, and a few others that recently opened. Car washes are going up all over the Minneapolis metro area. There will easily be three times as many standalone car washes once...
Last Post By: Cameron Wood Today, 2:37 PM

Lumber supply
Thread Starter: steven c newman
Has been restocked.. Bought 10 planks...for $30...had to cut a few of the 10 footers down, to fit into the Trunk of my Chevy Equinox... Eight 1 x 6 x 6' Five 1 x 4 x 6' And he threw in a stack of shorts And a 3/4" x 8" x 39" slab..
Last Post By: steven c newman Today, 5:15 PM

Braden Nichols

There is no available content written by Braden Nichols

Recent Polls
Would you borrow a tool from someone? (Votes: 71)

Sure - why not? (Votes: 9)

Never. If I needed something, I'd buy or rent it. (Votes: 10)

Maybe. Depends on the person and the tool. (Votes: 52)
Recent Forum Posts

Milling machine as a mortiser

Hopefully, they have a cap on the spindle retaining the drawbar ... so unscrewing it pops the tool from the spindle.

Otherwise, it's 'tapping'
Wes Grass Today, 10:51 PM

Grease..... and not the movie....

If you were paying to use Kluber grease you would be using as little as possible. Probably cheaper to buy a used motor with good bearings then the grease.
Bill Dufour Today, 10:45 PM

Harvey ST-1500 Sliding Table question

I'm guessing... sliding table attachment bolted to a 'conventional' tablesaw... at 'worst' it's at least as good as a miter gauge. Some distance further
Wes Grass Today, 10:42 PM

Milling machine as a mortiser

My Jet Mini mill is mt3 with a drawbar. Probably made around 1976.
BillD
Bill Dufour Today, 10:42 PM

liqudating entire wood shop

How much for the vacuum pump and all the fittings and everything that goes with it? Do you have the fittings to use with the 3520?
Sam Force Today, 10:24 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Braden Nichols

Recent Polls

Recent Forum Posts

Recent Blog Posts