• Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Jerome Stanek

    Glowforge release

    Thread Starter: Jerome Stanek

    I was wondering if Glowforge has sent out any units yet. I thought they were supposed to release the middle of December.

    Last Post By: Kev Williams Today, 4:20 PM Go to last post
    Ryan Pappas

    Hammer slider vs. Minimax

    Thread Starter: Ryan Pappas

    I have decided to sell my sawstop and get a sliding table saw. I have narrowed it down to hammer k3 79x48 and minimax. I have the SC2 and the SC4 in mind for minimax. Also adding in the SC3 to the mix. I mainly make end grain cutting boards so not sure if a full 8ft is necessary for me but I know...

    Last Post By: Jacob Mac Today, 1:25 PM Go to last post
    Brandon SPEAKS

    one premium plane

    Thread Starter: Brandon SPEAKS

    So this is mostly hypothetical. If you were to have a plane collection build on decent user vintage planes but could buy one premium LN or LV what would it be? A no 4 because of the advantages of perfectly tuned smoother plane? A specialty like a shooting plane and tracks for a shooting...

    Last Post By: lowell holmes Today, 3:01 PM Go to last post
    David Justice

    Reasons for Festool vs. Fein Dust Extractor

    Thread Starter: David Justice

    I have a DominoXL and just purchased a Festool sander and now want to get a dust extractor. According to the specs, they both have auto start, suction adjustment, HEPA and are quiet. The Fein has more CFM and higher water lift. So is there any reason to buy the Festool at almost $300 more? I...

    Last Post By: John Sanford Today, 2:24 PM Go to last post
    Clayton Dool

    Upgrade table saw worth it?

    Thread Starter: Clayton Dool

    I currently have a ts3650 with benchdog CI router insert. It works great. Runs smoothly. Have good blade guard with splitter. Probably needs to be re-tuned/aligned after 2 moves, but otherwise still very happy with it. Dust collection probably the only thing wish could improve, especially the...

    Last Post By: Jacob Mac Today, 3:28 PM Go to last post
    Larry Frank

    Help the Creek

    Thread Starter: Larry Frank

    I have read some postings about SMC and current financial issues. It appears there are many on here who are guests. Also, many are using ad blockers which hurt revenue. I am a contributor and it is well worth the very small cost. I also turned off the feature which prevents me from seeing...

    Last Post By: Jim Becker Today, 1:50 PM Go to last post
  • Don Jarvie

    There is no available content written by Don Jarvie
  • Recent Polls

    Which Coping Sled is the Best (Votes: 44)

    1. Woodpeckers Coping Sled (Votes: 16)

    2. Infinity Professional Coping Sled (Votes: 16)

    3. Neither - Who needs a sled anyway? (Votes: 10)

    4. Both - Why buy only one when you can have two at twice the price? (Votes: 2)

  • Recent Forum Posts

    ken hatch

    In The Short Rows

    Thanks Bill,

    I wouldn't mind (I think) being around in 50 years to see it . But there is not much chance, now the kids should be able to

    ken hatch Today, 4:22 PM Go to last post
    Kev Williams

    Glowforge release

    Old Captain Kirk
    while running back to work
    was reaching for his trusty phaser...

    then his face hit the floor
    because next

    Kev Williams Today, 4:20 PM Go to last post
    Len Mullin

    Attention Reed Gray

    Bill, if you turned to finished size, how do you then go about removing the melted wax?
    Len

    Len Mullin Today, 4:19 PM Go to last post
    David Bassett

    Narex Chisels - Comments on use

    It's hard to know what was done and how often and in what way. I think there is evidence that stones were flattened in the past, though maybe not as

    David Bassett Today, 4:11 PM Go to last post
    Carl Kona

    Going from NO DC to Oneida SDG . ductwork plan check.

    Rod,

    When I look at the Oneida curve I see 1510CFM @1.8" SP, which is stated to include the filter. So if someone determines they have

    Carl Kona Today, 4:06 PM Go to last post
  • Recent Blog Posts