• Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Michael Arruda

    Home Depot return policy change without notification

    Thread Starter: Michael Arruda

    Hello all, I had some small items left over from various things I've done around the house recently and decided to gather them up to take back to Home Depot. These items were purchased at various times over the past couple weeks and I of course misplaced my receipts. Meaning they got washed,...

    Last Post By: william watts Today, 1:05 AM Go to last post
    Tom Trees

    Suitable relay for three wire control on a VFD

    Thread Starter: Tom Trees

    Hello folks I have been walking through the steps with another forum member on setting up a VFD for his saw. Unfortunately the VFD does not have a relay OR COMMON for three wire control/push button station. Can any of you guys point me in the right direction to find a suitable relay for him? ...

    Last Post By: Tom Trees Today, 2:31 PM Go to last post
    Tim M Tuttle

    Jointer Safety

    Thread Starter: Tim M Tuttle

    I've been milling up a lot of white oak the past two nights. While I was using my jointer I started to ponder safety. For something like the table saw there are a lot of common safety procedures/dos/donts. A lot more than a jointer which makes sense as there are a lot more variables with the...

    Last Post By: David Zaret Today, 10:34 PM Go to last post
    Ronald Blue

    Two Year Old Camaster Stinger III

    Thread Starter: Ronald Blue

    I have a locally available Camaster Stinger III. It's a 4 X 8 machine with a three head setup. Whats the benefit of the three head arrangement? Is it an alternative to an ATC system? What's a fair price? He says it was $18,000 new. He's discounted it a lot from that amount. Nearly half. He did say...

    Last Post By: Keith Outten Today, 8:30 PM Go to last post
    Steve Rozmiarek

    Good quality mobility bases?

    Thread Starter: Steve Rozmiarek

    Anyone have recommendations on decent quality and reasonably priced mobility bases for table saws? I haven't paid any attention to the market in years, googled yesterday and was a little shocked at the prices I saw. Last I remember, they were half of what I'm seeing now. Bases for would cost...

    Last Post By: Randall J Cox Today, 10:55 AM Go to last post
    John Sincerbeaux

    Vacuum Fence for Slider

    Thread Starter: John Sincerbeaux

    Finally finished my vacuum tall fence for my slider. Made of commercially available parts from companies in the CNC industry. Aluminum T-slot plate 16 x 24 4) 4 x 4 aluminum pods pneumatic switch powered by vacuum pump from Vacuum clamping systems. The objectives for this fence were...

    Last Post By: Jeff Bartley Today, 7:46 PM Go to last post
  • Recent Polls

  • Recent Forum Posts

    David Zaret

    Jointer Safety

    i would put a vote in for lubricating the bed and fence, routinely, so the wood slides easily. the times when i've felt the most concerned for my safety

    David Zaret Today, 10:34 PM Go to last post
    Edward Dyas

    Ripping Blade

    The best rip blade I've used is actually a fiber cement blade where the 10" blade only had like 6 teeth.

    Edward Dyas Today, 10:31 PM Go to last post
    Edward Dyas

    plywood veneer delaminating

    Was it Purebond brand plywood? They are bad to not fill knot holes in the core veneers where the outer veneer is laid over a hole. You can't see it until

    Edward Dyas Today, 10:28 PM Go to last post
    Edward Dyas

    Jointer Safety

    For me I think the most dangerous aspect of a jointer is the push blocks they give you when you buy a new jointer. I tried them for about an hour with

    Edward Dyas Today, 10:23 PM Go to last post
    Bill Jobe

    Sill to concrete barrier

    I used a double 2x6 top sill (staggered studs)With the 2 shorter ends I have cut the top plates long enough to overlap the lower plate on both ends of

    Bill Jobe Today, 10:16 PM Go to last post
  • Recent Blog Posts