Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

What 8" jointer would you get and why?
Thread Starter: Alden Peterson
I think I'm finally going to pull the trigger on an 8" jointer. I don't have one right now and I'm tired of having to planer sled/table saw sled for jointing and not getting perfect cuts on those anyways. Prices are all over the place between brands. I'm wanting helical and probably...
Last Post By: Jared Sankovich Today, 12:28 PM

S7 or Exact 63?
Thread Starter: Albert Lee
Good day I have an opportunity to upgrade my Felder AD951 to something bigger, I have been wanting to separate the jointer and thickness planer for sometime. I am considering SCM L’Invincibile S7, and Felder/Format Exact 63. Luckily both machines are in stock and available for...
Last Post By: David Zaret Today, 8:15 AM

Using a ground as a neutral
Thread Starter: Wade Lippman
The VFD on my 120v Jet 1642 lathe burnt up and I would like to replace it with a 240v VFD. (they are smaller, cheaper, and more dependable than 120v) The only problem is that the tach requires 120v. I can put it on a separate 120v circuit, but that seems so inelegant. I would like to run a hot...
Last Post By: Brian Elfert Today, 2:08 PM

Do you have a whole house surge protector?
Thread Starter: dennis thompson
I’m thinking about getting a whole house surge protector. I’d appreciate any input from those of you who have one or anyone who has any info on them. Thanks
Last Post By: Brian Elfert Today, 3:12 PM

Joining Plywood
Thread Starter: tim walker
In building cabinets or any box, using butt joints and not using pocket screws, do you pre drill both pieces or just the starting piece?
Last Post By: Gordon Stump Yesterday, 5:28 PM

Selecting CBN wheel.
Thread Starter: Roger Davis TN
I want to buy one CBN wheel. I will use my other white aluminum oxide grinding wheels: a 120-grit wheel and a 60-grit wheel for shaping for now. I think I like the 1.5 inch wide and 220 grit CBN. Does anyone think this will be a good plan? Also, how do steel CBN wheels compare to aluminum wheels...
Last Post By: Randy Walker Today, 10:36 AM

Mike Henderson

There is no available content written by Mike Henderson

Recent Polls
Recent Forum Posts

Grizzly G0733

I'm not shopping Brice, I've had a Oneway 2436 since November 1998.
Richard Coers Today, 3:45 PM

Utility Trailer Bed Replacement--what to use?

Thanks all! Scott, I could go the solid lumber route, but the smooth surface is so nice when shoveling compost or the like out of the trailer. My equipment
Paul F Franklin Today, 3:44 PM

Need Delta 23-197 Grinder Help Pease...

Just measure the outside diameter. Huge difference between M12 and M16. Should be able to use a tape measure to figure that out.
Richard Coers Today, 3:41 PM

Paving the driveway

I almost went with concrete when we started to do this a few years ago. One problem I found is any concrete contractor I found planned to be very skimpy
John K Jordan Today, 3:32 PM

Do you have a whole house surge protector?

My parents had the control board in their furnace go out at least once a year. The HVAC tech recommended a good surge protector. I had a real nice (and
Brian Elfert Today, 3:12 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Mike Henderson

Recent Polls

Recent Forum Posts

Recent Blog Posts