Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Time for some levity
Thread Starter: Dave Anderson NH
With all of the negativity and political stuff going on with the Covid-19 virus it is time to look at the humorous side of things. Feel free to add more, but keep it clean or it will be deleted.
Last Post By: Dave Anderson NH Today, 10:49 AM

Milling machine as a mortiser
Thread Starter: andrew whicker
Hi all, I don't look often, but when I do it seems there are absolutely no used mortising machines out there. Something I've always wanted (someday) was a knee mill. There's a place near me that has had a Cincinnati Contour Master for sale forever (years and years). They re build these...
Last Post By: Joe Calhoon Today, 10:13 AM

Dumb answers to dumb questions
Thread Starter: Zachary Hoyt
I used to feel frustrated when I would have listed something for sale on Craigslist or Facebook and included the town where I lived, and instead of looking it up on their devices people would write to me to ask "where is Orwell" (where I used to live) or now "where is Piercefield?". I finally...
Last Post By: Ronald Blue Yesterday, 6:39 PM

Adhesive with a long open time
Thread Starter: Tim Andrews
Greetings All, I’ve done a search here, but all the threads I have seen are old. I would like a recommendation for an adhesive with a long open time for complicated glue ups, minimum 30 minutes,. I typically use Titebond 3 but would like more time for some projects. Sometimes it’s possible to do...
Last Post By: Jimmy Harris Today, 9:48 AM

landscaping is my other hobby, record for me, 25 yards of mulch
Thread Starter: Brian Runau
My landscape guys clean up the beds and install mulch for me now, too old, but I planted everything you see except the very large mature trees. Shade garden, cutting garden, front. Thanks Brian
Last Post By: Ronald Blue Yesterday, 6:55 PM

Harvey ST-1500 Sliding Table question
Thread Starter: Jay Houghton
I recently sold a machine I didn't need and now can repurpose that money into something else. I recently got a Sawstop and was thinking of the Harvey sliding table attachment for it. Expensive but it sure looks like the build quality is first class. You essentially get the Harvey miter gauge as...
Last Post By: Michael Burnside Today, 3:27 PM

Bruce Branson

There is no available content written by Bruce Branson

Recent Polls
Would you borrow a tool from someone? (Votes: 71)

Sure - why not? (Votes: 9)

Never. If I needed something, I'd buy or rent it. (Votes: 10)

Maybe. Depends on the person and the tool. (Votes: 52)
Recent Forum Posts

Harvey ST-1500 Sliding Table question

Agreed. Mine, with extension, is about 2-ish inches away from the blade. On short stock where that would matter I use a miter gauge anyway as I prefer
Michael Burnside Today, 3:27 PM

Harvey ST-1500 Sliding Table question

if you judge an Excalibur then consider there were likely five generations. I had two on one saw, they were first generation and primitive but on smaller
Warren Lake Today, 3:07 PM

Octagon Vent

That is exactly what I did, made a 16 inch square vent with the louvers then cut off the corners.
Just installed it today and the vent looks like
Mike Hanan Today, 3:05 PM

Harvey ST-1500 Sliding Table question

Hi Phil, in my opinion you should have the sliding table as close to the blade as possible.

Regards, Rod
Rod Sheridan Today, 2:48 PM

Vietnam veterans....

Spending too much time leaning over the computer keyboard is bad for my back, hips, knees and other stuff.
Bill D
Bill Dufour Today, 2:30 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Bruce Branson

Recent Polls

Recent Forum Posts

Recent Blog Posts