Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

How to bend wood like this - Outdoor furniture project
Thread Starter: Alan Lightstone
Looking for a new project to do. I've been spending a few months upgrading the workshop / fixing minor annoyances, and really need to actually build something. I ran across this in a magazine ad. The furniture is supposedly solid teak, though I don't think that will be in the cards for...
Last Post By: Mike King Today, 3:50 PM

Harvey Slider on Unisaw?
Thread Starter: John Kananis
All these slider threads got me thinking. Does anyone here have the Harvey compass st-1500 attached to their unisaw? Can you speak on the quality, ease of attachment, capabilities and shortcomings? Thank you in advance!
Last Post By: Troy Gamm Today, 7:09 PM

landscaping is my other hobby, record for me, 25 yards of mulch
Thread Starter: Brian Runau
My landscape guys clean up the beds and install mulch for me now, too old, but I planted everything you see except the very large mature trees. Shade garden, cutting garden, front. Thanks Brian
Last Post By: Brian Runau Today, 1:07 PM

SCM T130 bearing change
Thread Starter: Tom Yaegle
Has any one here done one? Looking for suggestions, thanks.
Last Post By: Bill Dufour Today, 7:16 PM

Lumber supply
Thread Starter: steven c newman
Has been restocked.. Bought 10 planks...for $30...had to cut a few of the 10 footers down, to fit into the Trunk of my Chevy Equinox... Eight 1 x 6 x 6' Five 1 x 4 x 6' And he threw in a stack of shorts And a 3/4" x 8" x 39" slab..
Last Post By: steven c newman Today, 6:05 PM

LLAMBRICH Intergrated arbor and chuck
Thread Starter: Patty Hann
Opinions, please on integrated arbor and chuck for a DP. Am looking at the LLAMBRICH Keyless chucks ... integrated 2MT shank/arbor 1/32" to 3/8" (part# JK10-MT2) 1/32" to 1/2" (JK13-MT2) Thanks
Last Post By: Patty Hann Today, 1:45 PM

Steve Vaughan

There is no available content written by Steve Vaughan

Recent Polls
Would you borrow a tool from someone? (Votes: 71)

Sure - why not? (Votes: 9)

Never. If I needed something, I'd buy or rent it. (Votes: 10)

Maybe. Depends on the person and the tool. (Votes: 52)
Recent Forum Posts

Swiss Army ... tool

My Uncle Hans would bring a Victorinox from Switzerland every time he came to visit. I was always so elated. A Swiss Army Knife without a knife is kind
Malcolm Schweizer Today, 7:19 PM

SCM T130 bearing change

I would buy and use. a pair of cheap needle nose pliers before going for too much hammering. Grind the tips to fit the slots on end. Use a big crescent
Bill Dufour Today, 7:16 PM

Harvey Slider on Unisaw?

Thanks. Not sure I will use the full 48" very often so I will most likely mount it flush. Would you happen to know off hand the max crosscut when
Troy Gamm Today, 7:09 PM

Bowl gouge measuring

When ordering spindle and bowl gouges I give the bar diameter I want, the other measurement is the distance across the top of the flutes, which will be
Don Stephan Today, 6:52 PM

Record player table

Very interesting design and excellent work.
Lee Schierer Today, 6:38 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Steve Vaughan

Recent Polls

Recent Forum Posts

Recent Blog Posts